JB/T 9046-1999 Grille Decontamination Machine

JB/T 9046-1999 JB/T 9046-1999 Grille Decontamination Machine JB/T9046-1999 Standard download decompression password: www.bzxz.net

ICS73.120
Machinery Industry Standard of the People's Republic of China
JB/T9046-1999
Gird sewerage machine
Published on 1999-06-28
State Bureau of Machinery Industry
Implementation on 2000-01-01
JB/T9046-1999
This standard is a revision of ZR188013-9 Gird sewerage machine. When it was accepted, the original standard was significantly revised, but the main technical content remained unchanged.
This standard replaces ZB8B013-90 from the date of implementation. This standard is proposed by the National Mining Machinery Standardization Technical Committee and the responsible unit is: Liuyang Mining Machinery Research Institute. The main drafters of this standard are: Li Xingwu, Li Jun, Zhang Juqi and Huang Leilin. Scope
Machinery Industry Standard of the People's Republic of China
Gird cewerage marhine
JB/T 9046—1999
ZBJ88013—5
This standard specifies the product classification of grille dirt remover: technical requirements, test methods, inspection rules, signs, labels, instructions, packaging, transportation and other requirements.
This standard refers to the ten grille dirt remover categories
2 Cited Standards
The following provisions are included in the standard and constitute the provisions of this standard by reference. At the time of publication of this standard, the versions indicated are valid. All standards are subject to revision. It is possible for parties citing this standard to use the latest version of the following specifications when making inquiries. GD:T172G—1979
GB-T 6388.-:986
GB:T 9969.1-- 1988
GB/T 13306--1991
JR/[1604--1994
3 Product classification
3.1 Model
Determination of small amount of paint
Transport packaging and receiving and sending signs
Products also use the total designation
Storage Sichuan Hangzhou Machinery Product Numbering System
Model number is in accordance with JB1604: Model representation method: R||t t||3.2 Marking examplewww.bzxz.net
Grid gap, mm
Grid width, dm
Grid sewage collector
Selection machinery
Grid width is 710mm, grid spacing is 14mm, for the grid sewage collector: its mark is: RG-714 grid sewage collector
3.3 Basic parameters
The basic parameters of the grid sewage collector shall comply with the provisions of Table 1. Approved by the State Bureau of Machinery Industry on 105-06-28
2000-01-01 implementation
phase determination
the source of the system
electric motor vehicle
grid combination case
grid source
motor power kw
4 technical requirements
RG-714RO-720
RG-201
RG-2023
JB7r9046-15
table reference
RG-725
RC1014RG1020RO1025
Rt-1111:14211k: 1-75
RC-2814RG-2820
RC-2625RG4014RG-402GRI-4G25
RG-2025
4.1 The grille decontamination machine shall meet the standard requirements and be manufactured according to the approved drawings and supporting documents. 4.2 The grille decontamination model shall be designed under the condition of sewage flow rate of 0.6.-1.0ms [1 00C:
3 All the parts in the case must be inspected and assembled, and the quality management documents shall be coordinated and assembled. 4.4 The grids shall meet the following requirements:
) The grid angle (the angle between the grid section and the small plane) is 45-75°, the first surface is flat, the second ... The scraper swings flexibly:
b) After reaching the plate position, it can be adjusted to obtain the best response to the handle and control the current situation. 4.9 The control part of the equipment has the following functions: 1) It can change the required movement direction of the transmission device and realize the up and down repetitive movement of the handle. 6) When the handle rail 1 slips or reaches too much force, it should be able to stop automatically and alarm. 4.10 The welds of each part are smooth, and defects such as burn-through, infantile effect, disaster and incomplete welding are allowed. 4.1 The outer surface of the machine belt is one foot and two layers of topcoat. If the paint film reaches the second level or above of GB 1720, 5 test methods
5.14.5c) The system length meets the requirements of 5.24.74.8 and 4.9 for operation adjustment. 6 Inspection and measurement
6. Inspection classification
The cleaning can be divided into inspection type or inspection type. 2
6.7 Delivery inspection
B.1046-1990
6.2.1 Each screen cleaning machine shall be inspected by the inspection department: when leaving the factory, the product quality certificate shall be attached. 6.2.2 The factory inspection shall meet the requirements of 4.4b), 4.5, 4.7 and 4.9. It can be inspected for 2 hours before leaving the factory, or it can be tested and inspected in parts. 6.3 Parallel inspection
0.3.1 In one of the following situations, the screen cleaning machine shall be inspected, when new products or old products are transferred to the factory for production: b) when the product is out of normal production, the material is wrong, the process has major changes; e) when the product has been discontinued for a long time and resumed production; ) the inspection result is very different from the last inspection; The national quality inspection machine shall be used according to the requirements of the planned inspection. (.3.2 Type control inspection items shall be printed on the template package. The new ones shall be shown in the template. (.3.3 Type control inspection items shall be printed on the template package. The qualified products shall be selected according to the factory inspection, and the unqualified products shall be drawn out according to the specifications. The signs, labels and instruction manuals shall be marked on the template package. 7. The world's first decontamination machine shall be produced for you: its type and size shall be consistent with G13, and the following contents shall be marked: a) manufacturer name and trademark: b) product name and model: ! Key technical parameters: d) factory number: 7.2 Road decontamination machine production and preparation of product instruction manuals. Its contents must meet the requirements of B 9.1: 8 Packaging, transportation and storage
5.1 The packaging of the grille dirt remover can be divided into parts: and the parts are wrapped 8.2 The grille dirt remover is accompanied by the following technical documents: 1) Product certificate or quality certificate;
b" Product instruction book:
) Packing list:
Product overview and installation drawing.
8.3 The packaging should be marked in a clear position, and its content should meet the requirements of GB/T6388. 8.4 The grille dirt remover should be stored under the condition of delay:
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.