JB/T 7940.6-1995 Needle valve type oil filling cup
time:
2024-08-13 05:48:57
- JB/T 7940.6-1995
- in force
Standard ID:
JB/T 7940.6-1995
Standard Name:
Needle valve type oil filling cup
Chinese Name:
针阀式注油杯
Standard category:
Machinery Industry Standard (JB)
-
Date of Release:
1989-02-10 -
Date of Implementation:
1990-01-01
China Standard Classification Number:
Machinery>>General Parts>>J21 Lubrication and Lubrication Devices
alternative situation:
Original standard number GB 1158-89Procurement status:
neq ISO B1575:1979
Description (Translated English) / downloadSkip to download
Summary:
JB/T 7940.6-1995 Needle Valve Oil Filling Cup JB/T7940.6-1995 Standard Download Decompression Password: www.bzxz.net
Standard contentSome standard content:
National Standard of the People's Republic of China
Drip-feed type lubricating cups
Drip-feed type lubricating cupsSubject content and scope of application
This standard specifies the types and dimensions of needle-feed type lubricating cups. This standard applies to mechanical oil lubricating cups on mechanical equipment. 2 Reference standards
GB1159 Technical conditions for lubricating cups
GB6172 Hexagonal thin nuts A and B grade chamfers
3 Types and dimensions
GB1158-89
Replaces GB.1158-79
Adjusted to J7940.6-95
The lubricating cups are divided into two types: A and B: Type A is shown in Figure 1, and Type B is shown in Figure 2. The dimensions are as specified in the table below Type A|| tt||Approved by the Ministry of Machinery and Electronics Industry of the People's Republic of China on February 10, 1989, and implemented on January 1, 1990
Minimum capacity
Marking example
GB1158-89
Minimum capacity 25cm, marking of type A needle valve oil cup: oil cup A25GB1158
Technical conditions
Technical conditions are in accordance with the provisions of GB1159.
Additional instructions:bzxz.net
This standard is proposed by the Ministry of Machinery and Electronics Industry.
Basic. Dimensions
Limit deviation
According to GB6172
This standard is under the jurisdiction of the Mechanical Standardization Research Institute of the Ministry of Machinery and Electronics Industry. This standard was drafted by the Science and Technology Information Institute of Shanghai Mechanical and Electrical Industry Administration Bureau and the Mechanical Standardization Research Institute of the Ministry of Machinery and Electronics Industry, and Shenyang Oil Cup Factory participated in the drafting.
The main drafters of this standard are Chen Huajin and Wang Xiliang. 13
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
Drip-feed type lubricating cups
Drip-feed type lubricating cupsSubject content and scope of application
This standard specifies the types and dimensions of needle-feed type lubricating cups. This standard applies to mechanical oil lubricating cups on mechanical equipment. 2 Reference standards
GB1159 Technical conditions for lubricating cups
GB6172 Hexagonal thin nuts A and B grade chamfers
3 Types and dimensions
GB1158-89
Replaces GB.1158-79
Adjusted to J7940.6-95
The lubricating cups are divided into two types: A and B: Type A is shown in Figure 1, and Type B is shown in Figure 2. The dimensions are as specified in the table below Type A|| tt||Approved by the Ministry of Machinery and Electronics Industry of the People's Republic of China on February 10, 1989, and implemented on January 1, 1990
Minimum capacity
Marking example
GB1158-89
Minimum capacity 25cm, marking of type A needle valve oil cup: oil cup A25GB1158
Technical conditions
Technical conditions are in accordance with the provisions of GB1159.
Additional instructions:bzxz.net
This standard is proposed by the Ministry of Machinery and Electronics Industry.
Basic. Dimensions
Limit deviation
According to GB6172
This standard is under the jurisdiction of the Mechanical Standardization Research Institute of the Ministry of Machinery and Electronics Industry. This standard was drafted by the Science and Technology Information Institute of Shanghai Mechanical and Electrical Industry Administration Bureau and the Mechanical Standardization Research Institute of the Ministry of Machinery and Electronics Industry, and Shenyang Oil Cup Factory participated in the drafting.
The main drafters of this standard are Chen Huajin and Wang Xiliang. 13
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- JB/T 6143.2-1992 Cone seal 90° cotton braided hose assembly
- JB/T 9172-1999 Gear nitriding and nitrocarburizing process and quality control
- JB/T 9158.6-1999 Dimensions of tool holder for horizontal multi-spindle automatic lathe with internal tool
- HG/T 2575-1994 Determination of the wetting power of surfactants - Immersion method
- GB/T 39261-2020 Nanotechnologies—Guidance on physico-chemical characterization of engineered nanoscale materials for toxicologic assessment
- JG 118-2000 Building seismic isolation rubber bearing
- HG/T 3695-2001 Acid Black P-7BR 150% (Weak Acid Black BR 150%)
- GB 191-2000 Packaging－Pictorial marking for handling of goods
- JB/T 6406.1-1992 Electric hydraulic block brake type, basic parameters and dimensions
- HG/T 2424-1993 Calcium stearate (light)
- GB/T 19012-2008 Quality management—Customer satisfaction—Guidelines for complaints handling in organizations
- GB/T 15275-1994 8-bit microcomputer STD bus
- CBM 2056-1982 Marine steel single leaf non-watertight door
- GB/T 15494-1995 手动轮椅车强度试验方法
- GB/T 19688.3-2005 Information and documentation--Bibliographic data element directory--Part 3;Information retrieval applications
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail：[email protected]