
JB/T 10115-1999 Machine tool fixture parts and components - Positioning shafts for lathes
time:
2024-08-12 02:24:54
- JB/T 10115-1999
- in force
Standard ID:
JB/T 10115-1999
Standard Name:
Machine tool fixture parts and components - Positioning shafts for lathes
Chinese Name:
机床夹具零件及部件 车床用定位轴
Standard category:
Machinery Industry Standard (JB)
-
Date of Release:
1999-08-06 -
Date of Implementation:
2000-01-01
Standard ICS number:
General, Terminology, Standardization, Documentation>>Vocabulary>>01.040.29 Electrical Engineering (Vocabulary)China Standard Classification Number:
Machinery>>Process Equipment>>J44 General Fixture
alternative situation:
Original standard number GB/T 12874-1991
Focal point Organization:
Mechanical Science Research InstitutePublishing Department:
Mechanical Science Research Institute

Skip to download
Summary:
JB/T 10115-1999 This standard specifies the locating shafts for lathes with Morse taper No. 2 to No. 6 and metric taper No. 80 to No. 100. This standard was first issued in 1983 as JB 3386-83 and first revised in 1991 as GB/T 12874-91. JB/T 10115-1999 Machine tool fixture parts and components locating shafts for lathes JB/T10115-1999 Standard download decompression password: www.bzxz.net

Some standard content:
IC5 28.060.41
Standard of the Machinery Industry of the People's Republic of China
Parts and units of jigs and fixtures for machine tools
Published on 1999-08-06
State Bureau of Machinery Industry
Implemented on 2000-01-01bzxz.net
Standard of the Machinery Industry of the People's Republic of China
Parts and units of jigs and fixtures for machine tools
Positioning shafts for lathes
The parts and units of jigs and fixtures for machine tools lathe
This standard specifies the lathe with the 2~6 taper and 80~100 taper. 2 Referenced Standards
JB/T10115—1999
The following standards contain provisions that are referenced in this standard and constitute the text of this standard. This standard is the current version 4, and the versions shown are all in effect. All standards will be revised, and the parties using and standardizing should discuss the possibility of using the new versions of the following standards. GB1298-1986 Carbon number paper core technical conditions Machine tool has its handle from the fire zone hoop
GB/T1443-1556
JB/T 8044-1599
3 Dimensions
Technical requirements for machine tool headstock parts and components
Size as shown in the figure below,
Approved by the State Machinery Industry Bureau on 1999-08-06
2000-01-01 Implementation
Quality
Rice surface
Deviation
4 Technical conditions
4.1 Material: T8 according to GB.T1298, 3
JB/T10115-1999
4.2 Heat treatment: 5B~64JIRC, 40~45EIRC, 4.3J-hela case JB/8044. 5 Marking
5.1 Marking example:
Nei quality 5, -35mm lathe end positioning shaft: positioning shaft 5-35JB/T101151999
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
Standard of the Machinery Industry of the People's Republic of China
Parts and units of jigs and fixtures for machine tools
Published on 1999-08-06
State Bureau of Machinery Industry
Implemented on 2000-01-01bzxz.net
Standard of the Machinery Industry of the People's Republic of China
Parts and units of jigs and fixtures for machine tools
Positioning shafts for lathes
The parts and units of jigs and fixtures for machine tools lathe
This standard specifies the lathe with the 2~6 taper and 80~100 taper. 2 Referenced Standards
JB/T10115—1999
The following standards contain provisions that are referenced in this standard and constitute the text of this standard. This standard is the current version 4, and the versions shown are all in effect. All standards will be revised, and the parties using and standardizing should discuss the possibility of using the new versions of the following standards. GB1298-1986 Carbon number paper core technical conditions Machine tool has its handle from the fire zone hoop
GB/T1443-1556
JB/T 8044-1599
3 Dimensions
Technical requirements for machine tool headstock parts and components
Size as shown in the figure below,
Approved by the State Machinery Industry Bureau on 1999-08-06
2000-01-01 Implementation
Quality
Rice surface
Deviation
4 Technical conditions
4.1 Material: T8 according to GB.T1298, 3
JB/T10115-1999
4.2 Heat treatment: 5B~64JIRC, 40~45EIRC, 4.3J-hela case JB/8044. 5 Marking
5.1 Marking example:
Nei quality 5, -35mm lathe end positioning shaft: positioning shaft 5-35JB/T101151999
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- SY/T 4100-1995 Technical specification for beach engineering survey
- JR/T 0181-2020 Futures contract elements
- GB/T 18839.2-2002 Preparation of steel substrates before application of paints and related products--Surface preparation methods--Abrasive blast-cleaning
- GB 4016-1983 Terminology of petroleum products
- GB/T 23244-2009 Fruit and vegetables - Principles and techniques of the controlled atmosphere method of storage
- GB/T 17980.145-2004 Pesticide-Guidelines for the field efficacy trials(II)-Part 145:Plant growth regulator efficacy trials on bloom and furit set of fruiter
- JB/T 3687.1-1999 Series of pedestal vibrating screens for mining
- HG/T 2269-1992 Technical requirements for mechanical seals for kettles
- GB 9053-1998 Stabilized light hydrocarbons
- GB 4543-1991 Orange smoke signal for life-saving
- GB 16754-1997 Mechanical safety emergency stop design principles
- GB 6222-1986 Gas safety regulations for industrial enterprises
- GB/T 3903.4-1994 General test method for footwear Hardness test method
- JB/T 9729-1999 Specification for the sample of the diameter sealing value of the plunger assembly, the oil delivery valve assembly and the injection nozzle assembly of diesel engine injection pump
- GB 17149.4-1997 Diagnostic criteria and treatment principles for cosmetic hair damage
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail:bzxznet@163.com