JB/T 2231.5-1999 Reciprocating piston compressor parts Part 5: Valve installation dimensions

JB/T 2231.5-1999 This standard is a revision of ZB J72 012-87 "Installation Dimensions of Reciprocating Piston Compressor Valves". The main technical content changes are as follows: - Added "reference standard" GB 1801 "Tolerance and fit dimensions to 500mm hole, shaft tolerance zone and fit"; - In order to prevent the wrong installation of inlet and exhaust valves, the relevant safety requirements for valve installation are specified. This standard is the fifth part of the JB/T 2231 "Reciprocating Piston Compressor Parts" series of standards, which includes the following five independent components: JB/T 2331.1: Shaft and pin outer dimensions JB/T 2331.2: Cylinder diameter JB/T 2331.3: Thin-walled bearings JB/T 2331.4: Ring valve discs JB/T 2331.5: Valve installation dimensions This standard specifies the installation dimension requirements of ring and mesh round valves for reciprocating piston compressors. This standard applies to annular and mesh valves for reciprocating piston compressors. This standard was first issued in 1977 and revised for the first time in 1987. JB/T 2231.5-1999 Reciprocating piston compressor parts Part 5: Valve installation dimensions JB/T2231.5-1999 Standard download decompression password: www.bzxz.net

1CS23.140
Machinery Industry Standard of the People's Republic of China
JB/T 2231.5-—1999
Reciprocating piston compressor parts
Part 5: Valve installation dimensions
Reciprocating piston compressor part-suhassemhtyPtrl 5:Overall dimensions for valveassembly1999-07-12Published
State Machinery Industry Bureau
2000-01-01 Implementation
JET2231.S-1999
This standard is a revision of ZBJ72012-R7 (Reciprocating Cleaning Machine Air Installation Dimensions): Compared with 2B1720012-8, the main technical changes are as follows: "=. Use the standard, print GDT18C1-1979 tolerance matching size requires 500mm hole, auxiliary belt matching 2 to prevent entry , push the gas Yin wrong installation, tough set the gas slow installation of the relevant requirements of the 4 ball standard is more than 2231 active case shrinkage mine palm parts "series standard frozen: part 1, this series standard includes: unique assembly part guard:
part 1 R233! .[: shaft, elimination diameter size
part gas diameter
part that is [Jiang bearing
part (that is 4: ring will be a piece bzxZ.net
part S Part JR:T 331.S This standard replaces ZB[72G12-4 standard from the date of implementation. The main drafting unit is: Erhaihui sheet metal pressing machine factory. The main drafting persons are: Yikang, Jinle Shou. Scope
Machinery Industry Standard of the People's Republic of China
Reciprocating piston compressor parts
Part 5: Valve installation dimensions
Reciprocating piston eumpressorpari-subussemblyPart S:Overall dimcnsions lor yalve assrmbly This standard specifies the requirements for the installation dimensions of annular and mesh polyhedral valves for reciprocating compressors. This standard applies to reciprocating pistons with annular and mesh gas plans (hereinafter referred to as abbreviated gas plans) 2 Reference standards
JB/2231.5-1999
The engraved mark contains the following information, which is used in this standard and constitutes the text of this standard: When this standard is used, the new version card is valid, and the standard department will be revised: When the source of this standard is used, the latest version of the standard may be eliminated: RT1-979 5m.1 hole, shaft tolerance zone and fit 3 installation dimensions
3.1 The installation dimensions of the ten-type quality air valve shall be in accordance with the provisions of 1 and 1. 2 The size of the closed type gas valve shall conform to the specifications of Figure 2 and Table 1. The State Administration of Machinery and Industry approved Figure 1 on July 12, 1999. Open type gas valve manufacturer 2000.01.0 Basic Science and Technology (1264) JB/T2231.5—1999 Figure 2 Closed circular gas valve height of each gas valve> 1.6-4.G
(e:28)
>4 0- 10. (
>10 :0-25
Limited brand store
≤ 2-
1ss381
IR/12231.5—19 99
Table system?
: P net
>en-I s
>1.6 -4.3
1 = 34)
1 53-
(#40:1c
1 e=+5F
Strong car plate limit difference
Limit end difference
JR/T2231.51999
(Kang:
Winter special M gas installation distance
>16-40
>ue-25
1 The diameter tolerance of the round gas company shall be in accordance with (10 specified in M11-1979, and the tolerance of the external public coupons shall be in accordance with 1X1-1979. The tolerance of the gas adjustment women's clothing should be in accordance with the requirements of 22 specified in 1X1-1979. The total tolerance of the sample key should be 3 with the general promotion number. Use the design of the six-space 4-gas test that can increase the need for gas solution or point-spring front shadow. The steel that is assembled is assembled due to the sparse state and the installation effect is reversed for the whole air intake and exhaust. The air is used in the outside size (). If there is a complete difference in the purchase flow of related parts, the air selection on the same machine will not be issued. Please fill in the certificate and then determine the safety table: Atmosphere:
Select the gas installation size.: Gas installation inside
Energy type gas space:
Safety size: Gas attachment installation is:
The numbers listed in the standard table are still successful.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.