JB/T 8013.2-1999 Thin-wall drill bushings for machine tool fixture parts and components
time:
1999-08-06 15:00:00
- JB/T 8013.2-1999
- in force
Standard ID:
JB/T 8013.2-1999
Standard Name:
Thin-wall drill bushings for machine tool fixture parts and components
Chinese Name:
机床夹具零件及部件 薄壁钻套
Standard category:
Machinery Industry Standard (JB)
-
Date of Release:
1999-08-06 -
Date of Implementation:
2000-01-01
Standard ICS number:
General, Terminology, Standardization, Documentation>>Vocabulary>>01.040.29 Electrical Engineering (Vocabulary)China Standard Classification Number:
Machinery>>Process Equipment>>J44 General Fixture
alternative situation:
Original standard number GB/T 12873-1991
Focal point Organization:
Mechanical Science Research InstitutePublishing Department:
State Machinery Industry Bureau
Description (Translated English) / downloadSkip to download
Summary:
JB/T 8013.2-1999 This standard specifies the thin-walled drill bushings with a specification of 0.5~7mm. This standard was first issued in 1991 as GB/T 12873-91. JB/T 8013.2-1999 Thin-walled drill bushings for machine tool fixture parts and components JB/T8013.2-1999 Standard download decompression password: www.bzxz.net
Standard contentSome standard content:
IC5 28.060.41
Standard of the Machinery Industry of the People's Republic of China
Parts and components of jigs and fixtures
The parts and units of jigs and fixtures1999-08-06 Issued
National Bureau of Machinery Industry
Implementation on 2000-01-01
Standard of the Machinery Industry of the People's Republic of China
Parts and components of jigs and fixtures
Thin wall drill bushings
This standard specifies the thin drill bushing with a size of 0.5~7mm. 2 Referenced standards
JBT8013.2—1999
The following standards contain the texts, and the referenced texts in the non-standards are the provisions of this standard. The published and revised versions of this standard are valid. All standards are subject to revision. Parties using this standard should explore the possibility of using the next edition of the standard. GB12186 Technical Conditions for Tool Steel
B8044-[9 State Technical Requirements for Machine Tool Parts and Components 3 Dimensions
The dimensions are shown in the following figure and table.
National Machinery Industry Bureau approved 1999-08-16 128
2100-01-01 implementation
: The tolerance is determined by the design
4 Technical conditions
JB/T8013.2—[999
4.1 Material: CTMn according to the provisions of GB299
4.2 Heat treatment: 5862HR core
4.3 Other technical conditions according to the provisions of JB/T8044: 5 MarkingbzxZ.net
5.1 Marking example:
L=6mm, thin drill with L=12m:
set 6×12JB/T 8013.2—199
Network deviation
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
Standard of the Machinery Industry of the People's Republic of China
Parts and components of jigs and fixtures
The parts and units of jigs and fixtures1999-08-06 Issued
National Bureau of Machinery Industry
Implementation on 2000-01-01
Standard of the Machinery Industry of the People's Republic of China
Parts and components of jigs and fixtures
Thin wall drill bushings
This standard specifies the thin drill bushing with a size of 0.5~7mm. 2 Referenced standards
JBT8013.2—1999
The following standards contain the texts, and the referenced texts in the non-standards are the provisions of this standard. The published and revised versions of this standard are valid. All standards are subject to revision. Parties using this standard should explore the possibility of using the next edition of the standard. GB12186 Technical Conditions for Tool Steel
B8044-[9 State Technical Requirements for Machine Tool Parts and Components 3 Dimensions
The dimensions are shown in the following figure and table.
National Machinery Industry Bureau approved 1999-08-16 128
2100-01-01 implementation
: The tolerance is determined by the design
4 Technical conditions
JB/T8013.2—[999
4.1 Material: CTMn according to the provisions of GB299
4.2 Heat treatment: 5862HR core
4.3 Other technical conditions according to the provisions of JB/T8044: 5 MarkingbzxZ.net
5.1 Marking example:
L=6mm, thin drill with L=12m:
set 6×12JB/T 8013.2—199
Network deviation
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- GB/T 27424-2020 Conformity assessment—Specification for biological quality control materials without metrological traceabilit
- GB/T 36080-2018 Application specification for barcode in cold chain logistics of agricultural products
- QX/T 515-2019 Characteristic value of meteorological element
- SY 0027-1994 Design specification for heavy oil gathering, transportation and steam injection system
- SL/T 235-1999 Geosynthetics Test Procedure
- GB 19085-2003 Requirement to protect contagious from business and service industry environment
- JB/T 6746.3-1993 Porcelain insulator rod support for electric precipitator
- GB/T 3880-1997 Aluminium and aluminium alloy rolled plates
- GB/T 11298.4-1997 Measurement methods for satellite television earth receiving stations - Indoor unit measurements
- GB 17859-1999 Criteria for the classification of computer information system security protection levels
- JB/T 5079-1991 Technical requirements for fuel tanks of small and medium power internal combustion engines
- JB/T 5318-1991 Technical conditions for large crawler cranes
- HG/T 2520-1993 Industrial phosphorous acid
- MT/T 588-1996 Technical requirements for explosion-proof diesel engine rubber-sleeved wheel/toothed rail vehicles for coal mines
- SY/T 5661-1995 Drilling fluid viscosity enhancer 80A51
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail：bzxznet@163.com