GB/T 2820.8-2002 Reciprocating internal combustion engine driven AC generator sets Part 8: Requirements and tests for small power generator sets

This part specifies the requirements, minimum performance and type tests of small power generating sets for land and marine use (civilian, recreational and industrial use) driven by reciprocating internal combustion engines. Aircraft generating sets are excluded. This part is mainly applicable to generating sets driven by reciprocating internal combustion engines with a voltage not exceeding 500V, single-phase or multi-phase, AC or DC. Such generating sets should be produced according to standards and can be selected from product samples or advertisements. In this part, "small power" means power below about 10kW. Small power generating sets applicable to this part have the following characteristics: - users are usually non-professionals (see 3.1 for details); - the whole generating set is usually transportable or mobile; - the power output adopts plug and socket connection (except for extra-low voltage, see 6.6.3); - users can use it without any additional installation. Generator sets with special purposes or larger power with the above characteristics can also be tested according to this part under the premise of approval by users and manufacturers. If additional requirements are required in certain use cases, the provisions of this part can be used as the basis. In addition to the definitions and requirements applicable in GB/T 2820.1 to 2820.6, this part also specifies specific requirements for testing and safety design. In addition, in order not to cause harm to users, this part also specifies relevant safety requirements. GB/T 2820.8-2002 Reciprocating internal combustion engine driven alternating current generator sets Part 8: Requirements and tests for small power generator sets GB/T2820.8-2002 standard download decompression password: www.bzxz.net

IS 79-160. 410
National Standard of the People's Republic of China
GB/T 2820.8—2002
Reciprocating internal combustion engine driven alternating current generating sets-Part 8.Reguirements and tests for low-power generating sets(1SO 8528-8:1995.MOD)
2002-08-05 Issued
The People's Republic of China
National Quality Supervision, Inspection and Quarantine Bureau
20030401 Implementation
G［282 Internal combustion engine driven alternating current generating units have a total of twelve parts: Part 1: Use, specification and performance 1508523-1993) Part 2 Engine 4TS) 2-1103
Part 3: Alternating current generators for 2-motor units (1S) 528-5.1!92 Part: Control devices and switchgear IS!)
Part 5: Generators (158528-51)
Part 1: Test 1c) 8128:03)
Part 7, Specification for the design of the replacement for this case (8523-7:14) Part 8, Requirements and test supervision for small power generators (18528:1, M01) Part 0 Measurement and evaluation of machine replacement 8%-1993 Part S852699.OD
Part 2 Emergency supply of safety equipment 1
Among them \ Part 1-: Online uninterruptible power supply system \ Recently commercial technology research THKAoNKAa
T 787C. 3-2C32
This part is modified to apply 15)-8:1 AC generator sets with multiple frequency internal combustion engines Part 1: Requirements and tests for small power generating sets.
This part is in (s/12820.1~223.5—1!% of the work, and proposes the factory's supplementary technical requirements and trial adjustment methods for the characteristics of small-power generation expansion units below 11:1W. It focuses on the safety thrust requirements and certification, marking, use and maintenance instructions of this type of unit. It is based on the standards 20.1--220. Modified and adopted by this part [based on 3528-1~628-6. This part is modified to adopt 14) 5523-8. This part must be consistent with 52820.1~3820.5—1! Used together with other standard signal stations.
Appendix A of this part is the data standard attachment.
This part is issued by the State Electric Vehicle Research and Development Commission. This part is under the jurisdiction of the Lanzhou Electric Vehicle Safety Institute. The main drafters of this part are: Zhang Shizhan, Wang Shiyu, Zu Xiaoxuan, and Pi Chen. 1 Scope
AC generator sets driven by reciprocating internal combustion engines GR/T2670.8—2002
Part 8: Requirements and tests for small power generator sets This part studies the requirements for low performance and test of small power generator sets driven by reciprocating internal combustion engines for international and marine (civil and industrial use): except for reciprocating generator sets. This part is intended for use with reciprocating internal combustion electric motors, but only single-phase or single-phase, real-time or DC generators. Such generators are not intended to be used in standard applications and can be selected from product samples or advertisements: In this part, the meaning of "small power" is power below 1 W: It is not possible to determine the small power limit. The small power generators applicable to this part have the following characteristics: The user is usually non-specialized (details in 3.1; the whole generator set is usually reduced to a dynamic type for testing Except for the low voltage connection method of the box door plug, see 6..3! ! The above-mentioned special points can be used without any additional installation. Under the premise of product manufacturing certification, the test can be carried out according to this part. In other cases where it is necessary to supplement the relevant requirements, the points in this part can be used as the basis. In addition to the definition requirements in GB/2820.1-2829., this part does not make specific provisions for the test and safety design.
In addition, in order to avoid causing harm to users and enterprises, some of the relevant safety requirements are also specified. ? Normative references
The following documents are referenced by the CB/T282 or are the clauses of this part. All referenced documents have been marked. All subsequent revisions (excluding the revised version and the inapplicable content of this part) will be considered. After the agreement is reached, the parties will study whether to use the new version of these documents. References that are out of date. The latest version applies to this part, G-00 Constant frequency performance of rotating machines (60c34-: 1G: T2520.1SS? Alternating current generator sets driven by internal combustion engines Part 1, Monthly ratings and non-energy S8523--: 1333:
GI2920.2: 1!9 Reciprocating internal combustion engine driven alternating current generators Part 2: Engine eV1S08526-2: 13933
GR/T 2R20-19S7
(cq1su)652a-3:1993)
Enterprise internal combustion engine alternator non-part of the first place, the output unit state alternator ti1/2320.4—1957
injection type internal wax machine cumulative alternator unit part 4: control device stomach type T beauty device kidney (qIS01 8b2k 1:1053)
In compound internal combustion engine driven alternating generator set: Part: Generator set (1508528-GRT2830.5-1997
GB/2820.6997 Compound internal combustion engine driven alternating generator set: Part: Test method (V1908523-61993
CB/T2820.8—2002
THIKoN KAca
GB/T072.200V reciprocating large internal combustion engine performance Part 1: Standard non-aggregate conditions, power vehicles, fuel consumption and oil consumption test method (ikll1s0s04e-1:1s95) 5: A fuel vehicle, dynamic spark ignition engine to seek the first line of electrical interference characteristics of the limit screen method tiltCiSPR!: 1t>
G 11/1424:1993 Internal combustion engine power station radio interference measurement methods and allowable values ​​​​as a guide (m1C:3:0701s equipment fast use drawings will be introduced and extracted IEC30034-5:1991 Travel transfer Part 5, complete power supply external charging expansion level 1FC50068-2-63:1991 Environmental test Part 2: Cold test test standard 91: Shock·Reverse resistance positive C503:! 5. Plug and socket standards for domestic and foreign purposes 14-4: 1: Two-terminal fixed voltage not exceeding 75V): 4: Flexible cable with thermal insulation resistance: >F60309-1: 19 Industrial plugs, sockets and connectors Part 1: General requirements 1EC 50109-7, 1985
"Industrial auxiliary sockets & connectors Part 1: Dimensions of core-mounted replacement parts
: 60335-: 11 Household and other electrical equipment - Part 1: Dual-purpose equipment - Part 4: Safety protection such as shock protection I7: 1 About 3 equipment using a single table of graphic symbols for non-inspection of gaps and explosion-proof spaces 1FC%29: 1 Enclosure protection level TF code?
3 Definitions
The following definitions are used in conjunction with the definitions in B81: 3.1
Non-professionals layia
Non-professionals are potential personnel who cannot recognize each other because of the danger of the project-promise or high overflow shooting
The whole process is in danger, and lacks certain and relevant knowledge, experience and training, and does not understand the specifications of the listed inflammation. 3-
Accessibility closeproximlty
Exploration of the whole system (including its whole motion specification) weekly cost has a deliberate rise. 3.3
Power rating
Rated power under rated frequency system: The power that can be achieved at the output terminal or socket of the generator.693 and other relevant national standards, the use of the net head socket connection method. The output of the circuit pin is higher than the rated voltage of the output plug socket can not slip. 5.6.4 Switching devices and connection points
The device for the embedded dynamic comparison effect, such as: measuring the false meter or the current action of the other ground leakage circuit breaker) should be installed in the switch box and meet the requirements of the resistance to dynamic.
The content of the system should be checked and verified. The measurement should be carried out within the specified range. 6.5.5 External components
The external components (especially the electromagnetic connection) of the AC generator/or the external components (especially the electromagnetic connection) should be protected to take into account the external generation and damage.
Check its performance during use,
6.6.6 Note
Under normal use, electronic components and other metal components are not included in the two bright, so that: other radioactive alloys, flame retardant, and steel with protective layer can be considered. E.5.7 Control and its connecting parts
The design of its connecting parts shall comply with: 63-! 5.7 Electric shock protection
9.7.1 The protection device shall comply with the provisions of 111.1, 112 and 12.2 of 1FC 6034-2-1:9. 5.7.2 The contact-breaking protection shall be in accordance with the provisions of JECfi0614·41.1992 Article 413. At the same time, the six standards of h.13.1-7.2.3 shall also be considered. [.1-27 The safety of the low-voltage material is defined in Article 11:2. [6.7.2.2 The design of the self-analysis of the grounding protection shall be in accordance with 1F:36:-1.1:12, 113.: The following conditions are except for the T system. In the TT system, only the leakage current protection device with a value of no more than 50A can be used. 1EC:609?-Formula 31-show
In the IT system, all exposed conductors should be replaced with protective conductors Find the concentrated ground, trust what situation sink F, technical ground electricity should be small ten taste ten 10
one in the system ten absolute continuous some release port power off device to avoid the following moment fault: frame first conductor Jiang any point out I one rapid correction self-current private generator voltage drop to below V (including shoot) IT, TTT's Ai: F,
5.7.2.3 gas protection should report 1E50364--1:1 in 41.5 regulations, sufficient allowance for 6.2.515.7.2. 3.2 specified indeed.
6.7.2.3.1 do not cultivate the structure of the generator set. Its bare metal 5 outside! etc. should be connected to the corresponding body. 6.7.2.3-2 If the "national electrical equipment is manufactured according to the law, the following cases must be met before the generator passes the test..." - When the final resistance between the live parts and the center position of the conductor drops below 1001V, the service point is in the center: the generator can be expanded. There is no need to limit the use of the system, and there is no need to consult the manufacturer when the micro-rate requirements occur. There is no limit on the length of the cable, wire or flexible conductor. When the total length is not more than "m, the live use and the total length are at least ten times the center V-: When the only thing exposed to the operator before the operation is exposed, the following changes must be met:
E6C3611-41:=932 Section 15.5.3.4 of the minimum automatic disconnection month. GB/T 282C.2002
In the time specified in 60e44-411992 Section 18.3.4, the output voltage of the generator terminal before the voltage drops below the new V (expansion).
Note that the generator will not be damaged when two related abnormalities are connected! The total amount of negative conductors is large, and the generator 4 of this standard is suitable for the generator 4, which meets the requirements of 6.2.3 and does not cause any danger to the user. The most important protection of the South African transformer meets the following requirements: When the loop center of the socket is 1., the generator can not directly reduce to the minimum or equal to the overcurrent protection device specified in 3.2.5. In addition, for multi-phase generators, the strain relief must be reported if there is a short circuit between the conductor of a phase and the conductor of the simplex. In order to reduce the short-circuit current in the generator, the protective circuit breaker that matches the generator cannot be used in this case (Insurance Law:
). The applicable attached protection features are as follows: a connection battery is installed on the generator unit. If there is a thermal conductor outside the generator, it should be connected to the power supply line and the ground connection should be carried out according to the technical management. If there is a permanent conductor, the permanent conductor cannot be connected to the molded protective wire and cannot be connected to the external power supply. In order to meet the requirements of this resistance limit value, the allowable length of the live wire is the appropriate information about the protection characteristics, including the number of cross sections.
Carry out H inspection and check according to the seat 1 .5 The ten-point test line of the station 7. The current is deep and the ground is painful. The new station or TV system is equipped with a new circuit breaker. The maximum current resistance is in accordance with the requirements of I5136141: 19! 3 in 4_3.1.3.5,413..1.2. The detection and protection records are sent and disassembled for the relevant contents in the instructions for use. The circuit breaker is described in the instructions for use. The current environment must be accurate and the circuit breaker must be installed and installed in the place where the power supply is required. Avoid the current environment specified in the instructions for use, and conduct daily inspections. 575 The current distribution network or a drinking distribution system is a batch of fiber-optic power generation systems. The products meet the requirements of the protection book in order to capture the overcurrent of the generator set with a tripping circuit breaker. Current, proceed with the test using the appropriate grounding resistance of 6.3. When the current of the secondary system does not exceed 1.5 of the value of the network benefit function of the power supply group after the supply is reported by the meter, the virtual current measurement (such as the current operation of the grounding circuit breaker) is connected to the positive and negative wires. The selective current drop of the circuit breaker is only used for the self-isolation of the generator set when the fuse is not fully calculated. The supply expansion system: the bottom of the loop resistance is 1, 2, and a short-circuit test is carried out and an inspection is carried out. 6. Mixed rise
and national group in the given card value "period, The temperature limit is not exceeded and the operating rate is at least allowed under the normal operating conditions. It is not allowed to exceed the allowable value specified by the manufacturer. 6.8.1 Generator
G is the first and gives the allowable temperature limit of the generator. When the generator is in the environmental conditions specified in Part 5 of the wood, the temperature rise test method of the foreign manufacturer is carried out. The temperature rise of the generator should be determined according to the standard of the high-speed test after the temperature rise test. The temperature rise of the whole generator should be measured according to the standard of the high-speed test. The generator should be less than the generator, and the amount of air or production should be more than the actual amount of the manufacturer. The manufacturer will not be qualified for GB/T 7820-8—200
Progressive improvement,
6.8.2 Temperature measurement of internal combustion engines and other components shall be conducted under the condition of thermal imaging. The leakage current and dielectric strength HKAoN KAa under working temperature shall not exceed the insulation capacity (capacity) specified by the manufacturer. The electrical equipment shall have sufficient insulation resistance. The provisions of 13.1 and 13.2 of E6m35-1155 are followed, and the transformer is tested according to the characteristics of 60.60 overload. In the use of the belt, the load should not be corrected. The generator that is tested with this standard shall not be damaged by overload. 6.0.1 Non-controlled generators. The speed and speed of the generator set will not decrease when the load is increased. The load limit is determined accordingly: the generator set is operated at a rated power of 7.1 under the external load specified in the British 5 case and the operating mode is verified. The generator set is loaded with active power until the agreed power or current is reached. The rated value is 80%. The correct working point is determined: the test transformer protection device trips after the test transformer is tested for no more than m. During the cold test, the load of the generator set shall be maintained at the set value: the power of the generator set shall be proportional to the load point and the limit of the engine shall be set. When the speed is insufficient, the generator must be protected to prevent overheating. This device shall be used, but it shall not automatically return to its original position. When the power of the generator set exceeds its set value, the power output (before oil) will decrease suddenly before the start: after that, a power test shall be carried out, and the connection shall be evaluated according to the provisions of 1. 6.11 Abnormal operation
6.11.1. The generator can reach the rated power only under the specified cooling environment. If the working conditions do not meet the requirements of the standard, such as the generator set is not in good condition (limited area), then the alternating current must be reduced. These situations can be described in the instruction manual. Check according to the current requirements of the instruction card
6.11.2 Any short circuit in the power output of the generator will not cause mechanical or electrical damage that affects the safety of the enterprise. This requirement also applies to the connection of appropriate filters in the chemical industry, and also includes the situation of reverse polarity of the charging battery. When the rated voltage is positive, if the voltage is selected by mistake, it will cause great damage to the safety of the generator set. Make the generator set run to a stable state. At the same time, only the work can be carried out by the end of the load or the end of the load to break the test. The state should be confirmed. After the test, any protective trigger that has been activated will be reset or reset. Put the generator set with a charger and a fully charged battery in full test: the end or the cargo leaks reversely, accounting for the total number of times in these tests. During the period, the heart does not emit open flames or metal-transforming agents - there is a rate of three-dimensional or natural gas method that cannot prove the effectiveness of the test plan. The deformation agent should be used in the sound environment of the vehicle test. The battery is decorated with a mountain pool. There is no fixed source. The wind point is equal to the direct description of the generator battery. The capacity is not specified. There is such a mark on the battery charger: the charging benefit can be asked regardless of the company model. The battery charger is also in each case. The test drawing and the maximum capacity of the battery are marked on the red or The value of 6-.3 in the manual of the production of the civil industry is determined to ensure that the speed control of the motor is installed. The generator is equipped with a protective device to prevent users from misusing it. When the motor is not closed, the controller and the block data may be closed. When the rated reverse speed is not reached, the motor cannot start and the motor is damaged.
The generator is recorded at 2 times the rated reverse speed: m, and then the daily ratio of the structure is observed. 6.12 Electrical distance and electrical isolation
GR/T 2820.8—2002
The width of the electrical room shall not be less than the provisions of IEC5051:11 Section 29, and its unit is m: it should be verified by measurement and based on production and operation, and its compliance should be controlled. 6.13 Components of electrical equipment
For electrical components that are more important for safety, they should meet the applicable ISO standards and safety performance requirements in relevant standards. The marking of these components is for operating effectiveness: when they are used in the machine, they must be avoided. These current regulations must be followed for independent components: this standard is not sufficient. Generally speaking, the following general conditions shall be carried out separately for independent parts. If there are any differences and technical specifications, please note that In this case, the product shall be tested according to the instructions. In this case, the product shall be tested according to the instructions of the manufacturer. If there is no corresponding, correct and national standard, the manufacturer shall read the instructions carefully and then use the specified test items for testing. In this case, the number of test items shall be similar to the specified specifications. It shall be verified by the relevant technical specifications, national standards or specific product specifications, and its compliance shall be verified by daily testing. 7 Operating characteristics, power output, performance and fuel consumption. 1 Standard environment set Standard conditions GB/6972-1 Current starting temperature: Atmospheric pressure: 1 kPa :
-Relative humidity: 310%:
7.2 Starting and operating conditions
The generator set in accordance with this standard can be operated within an ambient temperature range of 15~4U.7.3 Determination of power output, performance level and voltage tolerance7-3.1 Prepare and start the generator set according to the instructions. After the compound internal combustion engine has been running for about 10 minutes, the voltage at the lower disk and the upper limit of the plate are set.3.2 The generator set is operated at the average allowable power factor and the specified power factor for at least 10 minutes, and the power generation is continuously loaded from no-load to the rated power factor.
Check whether the power after heating is within the range of GB/12826.51997 16.:, 6.515.7 and 16.1 of Class G.
Any power can be measured directly with an internal power meter. The power can be obtained by calculating the power and the electrical engineering data. During the measurement, the atmospheric pressure and ambient temperature of the test site are consistent with the standard environmental conditions (current 7.1), and the relevant test values ​​of the internal combustion engine should be corrected according to GB/T6C72.1: The power characteristics obtained under the standard environmental conditions should not be less than 5% of the rated power for the machine type and should not be less than 11% of the rated power for the H class machine type.
7.3.3 The fuel consumption rate of the small-rate generator line shall be calculated under the fixed power room, and the value of the single micro-6kW·h shall comply with the provisions of GB.1: The micro-consumption can be used as a unit, 7. Radio interference suppression
When designing the generator set, its monthly gas annual radio interference suppression limit range shall comply with the requirements of/12: The no-load interference limit value of the spark ignition type internal engine 31 edition
Install a large-line electric shock-resistant device, which will not have an adverse effect on the electrical and control safety of the generator set. According to tk1402G1571221, it complies with the requirements
8 Marking
The label on the old unit is solid and easy to recognize, 9
G/T 2820-B2002
8.1 Rating plate
The rated power and actual performance level of the generator set should be based on the rated power to prove the single blank standard. -TYY KANr KAa
The standard number of the electric induced unit is the cumulative number of the original tax (H672.1 The standard of the original tax is the whole hundred: Therefore, before the point of the rating, the installation site of the play industry and the environment competition can be carried out briefly, and the rating plate can be used to connect the GT industry in the second 4 The heat of the single set is to be carried out
by the recognized method to check its compliance:
3.2? Safety and information signs
The symbols of the signs should be in accordance with the provisions of the IS) heart, and the power generation must be permanent. The following instructions are given for use:) Please use it when:
: There is a change in the flue gas, please do not add a pull pool in the room where the door is not open.
It can be ignited and the components can be properly aged. You should know or use the protection control kinetic energy with kindness. The different types of twists and turns of the group and the requirements of the local authorities are the signs of the Sichuan system test 9 Instructions for use Safety instructions
The heart of the unit may cause accidental injury, which is not recognized by the professional history. As long as the enterprise is correct! The knowledge of the kinetic energy of the generator set should be mastered in the safety manual of the generator set driven by the RK engine. The following safety, operation and re-ignition requirements should be included in the following:) General safety knowledge
should include the following contents,
1: Keep a certain safety distance between the generator set and the engine: Oil is flammable and has a large capacity. You cannot add oil during the operation of the engine. You cannot smoke when refueling. You can also not approach the oil container during the operation of the engine.
3! The temperature of the internal parts is high, which may cause burns. The warning sign of the engine fiber F should be issued. 4) If there is a gas layer in the engine, it is not allowed to operate in an unrealistic room. When the unit is installed in a room with good ventilation, you must pay special attention to the fire.
h: Electric safety Kai
includes the following internal tests:
1, gas equipment: mood power system and disease head connection parts. 2》Agricultural generator sets can also be connected to other power sources. When connected with the power system library as the user, the whole party's technical personnel on the power supply to complete the power flow card to the public power grid and the generator core correction difference. According to the current provisions of this standard, this difference is described in the use of the representative drama. 3) The power output is connected to the heat exchanger, and the circuit breaker is connected to the generator set: If the circuit breaker is replaced with a new one, it must be replaced with a circuit breaker with the same special performance characteristics. 4) If the generator set complies with the electrical modification requirements specified in 6.2.3 of this standard, the following should also be considered:) The generator is connected properly.
6) Use extended wires or movable distribution cabinets: The total length of the conductor end is 1m. The total length of the conductor end is 2.5mm, and the total length of the conductor is not more than 10ml.) The safety factor of the movable
is to fully understand the function and position of each device, whether it can be displayed or not,2 Any short circuit in the correct power output of the generator will not cause mechanical or electrical damage that affects safety. This also applies to the connection of filters in the chemical industry, including the reverse polarity of the charging battery. When the rated voltage is positive, if the voltage is selected by mistake, it will cause serious damage to the safety of the generator set. Make the generator set run to a stable state. At the same time, only the power supply or load end can be disconnected to conduct a comprehensive test. It should be confirmed that the state is correct. After the test, any protective devices that have been activated have been reset or reset. Put the generator set with a charger and a fully charged battery in full connection: the two ends or the goods are effectively leaking liquid, accounting for a certain number of times. During these tests, the generator set shall not emit open flames or metal-transforming agents. The rate of deformation of the natural gas method cannot be proved. The battery is the same as the generator set battery. The direct current meter is drawn out, and the capacity is equal to the rated power. Regarding the quantity, there is such a mark on the battery charger: The charging benefit can be asked regardless of the company's model. In each case, the battery can be charged in accordance with the test drawing and the maximum power consumption value of 6-.3. The red mark on the red mark or the production manual indicates that the motor speed control must be installed. The generator is equipped with advanced protection to avoid user misuse. When the car is not closed step by step, the controller and the block data may be severely damaged when the rated reverse speed is not started and the generator is about 2 times the rated speed. Record the generator at 2 times the rated speed: m, and then observe the daily conversion ratio. 6.12 Electrical distance and electrical isolation GR/T 2820.8—2002 The electrical distance from the room should not be less than the provisions of IEC5051:11 Section 29, and the unit is m. It should be verified by measurement and production operation, and its compliance should be verified. 6.13 Components of electrical equipment The most important electrical components for safety should meet the applicable safety performance requirements of relevant standards. The marking of these components is the operating efficiency: when they are used in the machine, they must avoid these conditions, and the test of the independent components must meet the corresponding specifications: this standard is not enough. For example, if there is a separate part and the technical instructions are used, the test should be carried out according to the specified period. In this case, the total number of test materials shall be similar to the specified period. 7 Operating characteristics, power output, performance and fuel consumption. 1 Standard environmental components
Standard conditions GB/6972-1 Starting temperature:
Atmospheric pressure: 1 kPa :
Relative humidity: 3-10%:
7.2 Starting and operating conditions
The generator set that complies with this standard can be started and operated within an ambient temperature range of 15~4U. 7.3 Determination of power output, performance level and voltage tolerance 7-3.1 Prepare and start the generator set according to the instructions on the instruction card. After the compound internal combustion engine is about mn, the power generation unit shall be operated at least at the average allowable power rate and the current power rate of the power generator according to the voltage and the upper limit of the plate. The power generation unit shall be operated at least at the average allowable power rate and the current power rate of the power generator according to the no-load residual load gradually to the rated power rate.
Check whether the power and power of the power generator after heating are full of GB/12826.51997 16.:6.515.7 and 16.1 G-level specifications.
Any power can be directly measured with an internal power meter. The power rate can be obtained by calculating the reverse seven certificates and the electrician's case. During the measurement period, if the atmospheric pressure and ambient temperature at the test location are consistent with the standard environmental conditions (see 7.1), the relevant test values ​​of the internal combustion engine shall be modified according to GB/T 6C72.1: the power characteristics obtained under standard environmental conditions shall not be less than 5% of the rated frequency and power for Class H machines; for Class H machines, it shall not be less than 11% of the rated average power.
7.3.3 The fuel consumption rate of the small-rate generator line shall be calculated under the fixed power room, and the value of the single micro-6kW·h shall comply with the provisions of GB.1: The micro-consumption can be used as a unit, 7. Radio interference suppression
When designing the generator set, its monthly gas annual radio interference suppression limit range shall comply with the requirements of/12: The no-load interference limit value of the spark ignition type internal engine 31 edition
Install a large-line electric shock-resistant device, which will not have an adverse effect on the electrical and control safety of the generator set. According to tk1402G1571221, it complies with the requirements
8 Marking
The label on the old unit is solid and easy to recognize, 9
G/T 2820-B2002
8.1 Rating plate
The rated power and actual performance level of the generator set should be based on the rated power to prove the single blank standard. -TYY KANr KAa
The standard number of the electric induced unit is the cumulative number of the original tax (H672.1 The standard of the original tax is the whole hundred: Therefore, before the point of the rating, the installation site of the play industry and the environment competition can be carried out briefly, and the rating plate can be used to connect the GT industry in the second 4 The heat of the single set is to be carried out
by the recognized method to check its compliance:
3.2? Safety and information signs
The symbols of the signs should be in accordance with the provisions of the IS) heart, and the power generation must be permanent. The following instructions are given for use:) Please use it when:
: There is a change in the flue gas, please do not add a pull pool in the room where the generator is not working.
It can be ignited and the components can be properly aged. You should be aware of or use the protection control kinetic energy to reduce the aging of the components. The different types of twists and turns of the group and the requirements of the local authorities are the signs of the Sichuan system test 9 Instructions for use Safety instructions
The generator may cause accidental injury early, and the professional history is not recognized. As long as the enterprise is correct! The knowledge of the kinetic energy of the generator set should be mastered in the safety manual of the generator set driven by the RK engine. The following safety, operation and re-ignition requirements should be included in the following:) General safety knowledge
should include the following contents,
1: Keep a certain safety distance between the generator set and the engine: Oil is flammable and has a large capacity. You cannot add oil during the operation of the engine. You cannot smoke when refueling. You can also not approach the oil container during the operation of the engine.
3! The temperature of the internal parts is high, which may cause burns. The warning sign of the engine fiber F should be issued. 4) If there is a gas layer in the engine, it is not allowed to operate in an unrealistic room. When the unit is installed in a room with good ventilation, you must pay special attention to the fire.
h: Electric safety Kai
includes the following internal tests:
1, gas equipment: mood power system and disease head connection parts. 2》Agricultural generator sets can also be connected to other power sources. When connected with the power system library as the user, the whole party's technical personnel on the power supply to complete the power flow card to the public power grid and the generator core correction difference. According to the current provisions of this standard, this difference is described in the use of the representative drama. 3) The power output is connected to the heat exchanger, and the circuit breaker is connected to the generator set: If the circuit breaker is replaced with a new one, it must be replaced with a circuit breaker with the same special performance characteristics. 4) If the generator set complies with the electrical modification requirements specified in 6.2.3 of this standard, the following should also be considered:) The generator is connected properly.
6) Use extended wires or movable distribution cabinets: The total length of the conductor end is 1m. The total length of the conductor end is 2.5mm, and the total length of the conductor is not more than 10ml.) The safety factor of the movable
is to fully understand the function and position of each device, whether it can be displayed or not,2 Any short circuit in the correct power output of the generator will not cause mechanical or electrical damage that affects safety. This also applies to the connection of filters in the chemical industry, including the reverse polarity of the charging battery. When the rated voltage is positive, if the voltage is selected by mistake, it will cause serious damage to the safety of the generator set. Make the generator set run to a stable state. At the same time, only the power supply or load end can be disconnected to conduct a comprehensive test. It should be confirmed that the state is correct. After the test, any protective devices that have been activated have been reset or reset. Put the generator set with a charger and a fully charged battery in full connection: the two ends or the goods are effectively leaking liquid, accounting for a certain number of times. During these tests, the generator set shall not emit open flames or metal-transforming agents. The rate of deformation of the natural gas method cannot be proved. The battery is the same as the generator set battery. The direct current meter is drawn out, and the capacity is equal to the rated power. Regarding the quantity, there is such a mark on the battery charger: The charging benefit can be asked regardless of the company's model. In each case, the battery can be charged in accordance with the test drawing and the maximum power consumption value of 6-.3. The red mark on the red mark or the production manual indicates that the motor speed control must be installed. The generator is equipped with advanced protection to avoid user misuse. When the car is not closed step by step, the controller and the block data may be severely damaged when the rated reverse speed is not started and the generator is about 2 times the rated speed. Record the generator at 2 times the rated speed: m, and then observe the daily conversion ratio. 6.12 Electrical distance and electrical isolation GR/T 2820.8—2002 The electrical distance from the room should not be less than the provisions of IEC5051:11 Section 29, and the unit is m. It should be verified by measurement and production operation, and its compliance should be verified. 6.13 Components of electrical equipment The most important electrical components for safety should meet the applicable safety performance requirements of relevant standards. The marking of these components is the operating efficiency: when they are used in the machine, they must avoid these conditions, and the test of the independent components must meet the corresponding specifications: this standard is not enough. For example, if there is a separate part and the technical instructions are used, the test should be carried out according to the specified period. In this case, the total number of test materials shall be similar to the specified period. 7 Operating characteristics, power output, performance and fuel consumption. 1 Standard environmental components
Standard conditions GB/6972-1 Starting temperature:
Atmospheric pressure: 1 kPa :
Relative humidity: 3-10%:
7.2 Starting and operating conditions
The generator set that complies with this standard can be started and operated within an ambient temperature range of 15~4U. 7.3 Determination of power output, performance level and voltage tolerance 7-3.1 Prepare and start the generator set according to the instructions on the instruction card. After the compound internal combustion engine is about mn, the power generation unit shall be operated at least at the average allowable power rate and the current power rate of the power generator according to the voltage and the upper limit of the plate. The power generation unit shall be operated at least at the average allowable power rate and the current power rate of the power generator according to the no-load residual load gradually to the rated power rate.
Check whether the power and power of the power generator after heating are full of GB/12826.51997 16.:6.515.7 and 16.1 G-level specifications.
Any power can be directly measured with an internal power meter. The power rate can be obtained by calculating the reverse seven certificates and the electrician's case. During the measurement period, if the atmospheric pressure and ambient temperature at the test location are consistent with the standard environmental conditions (see 7.1), the relevant test values ​​of the internal combustion engine shall be modified according to GB/T 6C72.1: the power characteristics obtained under standard environmental conditions shall not be less than 5% of the rated frequency and power for Class H machines; for Class H machines, it shall not be less than 11% of the rated average power.
7.3.3 The fuel consumption rate of the small-rate generator line shall be calculated under the fixed power room, and the value of the single micro-6kW·h shall comply with the provisions of GB.1: The micro-consumption can be used as a unit, 7. Radio interference suppression
When designing the generator set, its monthly gas annual radio interference suppression limit range shall comply with the requirements of/12: The no-load interference limit value of the spark ignition type internal engine 31 edition
Install a large-line electric shock-resistant device, which will not have an adverse effect on the electrical and control safety of the generator set. According to tk1402G1571221, it complies with the requirements
8 Marking
The label on the old unit is solid and easy to recognize, 9
G/T 2820-B2002
8.1 Rating plate
The rated power and actual performance level of the generator set should be based on the rated power to prove the single blank standard. -TYY KANr KAa
The standard number of the electric induced unit is the cumulative number of the original tax (H672.1 The standard of the original tax is the whole hundred: Therefore, before the point of the rating, the installation site of the play industry and the environment competition can be carried out briefly, and the rating plate can be used to connect the GT industry in the second 4 The heat of the single set is to be carried out
by the recognized method to check its compliance:
3.2? Safety and information signs
The symbols of the signs should be in accordance with the provisions of the IS) heart, and the power generation must be permanent. The following instructions are given for use:) Please use it when:
: There is a change in the flue gas, please do not add a pull pool in the room where the generator is not working.
It can be ignited and the components can be properly aged. You should be aware of or use the protection control kinetic energy to reduce the aging of the components. The different types of twists and turns of the group and the requirements of the local authorities are the signs of the Sichuan system test 9 Instructions for use Safety instructions
The generator may cause accidental injury early, and the professional history is not recognized. As long as the enterprise is correct! The knowledge of the kinetic energy of the generator set should be mastered in the safety manual of the generator set driven by the RK engine. The following safety, operation and re-ignition requirements should be included in the following:) General safety knowledge
should include the following contents,
1: Keep a certain safety distance between the generator set and the engine: Oil is flammable and has a large capacity. You cannot add oil during the operation of the engine. You cannot smoke when refueling. You can also not approach the oil container during the operation of the engine.
3! The temperature of the internal parts is high, which may cause burns. The warning sign of the engine fiber F should be issued. 4) If there is a gas layer in the engine, it is not allowed to operate in an unrealistic room. When the unit is installed in a room with good ventilation, you must pay special attention to the fire.
h: Electric safety Kai
includes the following internal tests:
1, gas equipment: mood power system and disease head connection parts. 2》Agricultural generator sets can also be connected to other power sources. When connected with the power system library as the user, the whole party's technical personnel on the power supply to complete the power flow card to the public power grid and the generator core correction difference. According to the current provisions of this standard, this difference is described in the use of the representative drama. 3) The power output is connected to the heat exchanger, and the circuit breaker is connected to the generator set: If the circuit breaker is replaced with a new one, it must be replaced with a circuit breaker with the same special performance characteristics. 4) If the generator set complies with the electrical modification requirements specified in 6.2.3 of this standard, the following should also be considered:) The generator is connected properly.
6) Use extended wires or movable distribution cabinets: The total length of the conductor end is 1m. The total length of the conductor end is 2.5mm, and the total length of the conductor is not more than 10ml.) The safety factor of the movable
is to fully understand the function and position of each device, whether it can be displayed or not,）Activities
To collect safety rate and operation information, fully understand the functions and positions of each device,）Activities
To collect safety rate and operation information, fully understand the functions and positions of each device,8—2002
The width of the electrical room shall not be less than the provisions of IEC5051:11 Section 29, and its unit is m: it shall be verified by measuring the gas and based on production and operation, and its compliance shall be controlled. 6.13 Components of electrical equipment
For electrical components that are important for safety, they shall meet the applicable IS standards and the safety performance requirements in the relevant standards. The marking of these components is the operating efficiency: when they are used in the machine, they must avoid these current requirements, and the test of the independent components must comply with the corresponding specifications: this standard is not enough. For example, if there is a separate part and the technical instructions are used, the test should be carried out according to the specified period. In this case, the total number of test materials shall be similar to the specified period. 7 Operating characteristics, power output, performance and fuel consumption. 1 Standard environmental components
Standard conditions GB/6972-1 Starting temperature:
Atmospheric pressure: 1 kPa :
Relative humidity: 3-10%:
7.2 Starting and operating conditions
The generator set that complies with this standard can be started and operated within an ambient temperature range of 15~4U. 7.3 Determination of power output, performance level and voltage tolerance 7-3.1 Prepare and start the generator set according to the instructions on the instruction card. After the compound internal combustion engine is about mn, the power generation unit shall be operated at least at the average allowable power rate and the current power rate of the power generator according to the voltage and the upper limit of the plate. The power generation unit shall be operated at least at the average allowable power rate and the current power rate of the power generator according to the no-load residual load gradually to the rated power rate.
Check whether the power and power of the power generator after heating are full of GB/12826.51997 16.:6.515.7 and 16.1 G-level specifications.
Any power can be directly measured with an internal power meter. The power rate can be obtained by calculating the reverse seven certificates and the electrician's case. During the measurement period, if the atmospheric pressure and ambient temperature at the test location are consistent with the standard environmental conditions (see 7.1), the relevant test values ​​of the internal combustion engine shall be modified according to GB/T 6C72.1: the power characteristics obtained under standard environmental conditions shall not be less than 5% of the rated frequency and power for Class H machines; for Class H machines, it shall not be less than 11% of the rated average power.
7.3.3 The fuel consumption rate of the small-rate generator line shall be calculated under the fixed power room, and the value of the single micro-6kW·h shall comply with the provisions of GB.1: The micro-consumption can be used as a unit, 7. Radio interference suppression
When designing the generator set, its monthly gas annual radio interference suppression limit range shall comply with the requirements of/12: The no-load interference limit value of the spark ignition type internal engine 31 editionbzxZ.net
Install a large-line electric shock-resistant device, which will not have an adverse effect on the electrical and control safety of the generator set. According to tk1402G1571221, it complies with the requirements
8 Marking
The label on the old unit is solid and easy to recognize, 9
G/T 2820-B2002
8.1 Rating plate
The rated power and actual performance level of the generator set should be based on the rated power to prove the single blank standard. -TYY KANr KAa
The standard number of the electric induced unit is the cumulative number of the original tax (H672.1 The standard of the original tax is the whole hundred: Therefore, before the point of the rating, the installation site of the play industry and the environment competition can be carried out briefly, and the rating plate can be used to connect the GT industry in the second 4 The heat of the single set is to be carried out
by the recognized method to check its compliance:
3.2? Safety and information signs
The symbols of the signs should be in accordance with the provisions of the IS) heart, and the power generation must be permanent. The following instructions are given for use:) Please use it when:
: There is a change in the flue gas, please do not add a pull pool in the room where the generator is not working.
It can be ignited and the components can be properly aged. You should be aware of or use the protection control kinetic energy to reduce the aging of the components. The different types of twists and turns of the group and the requirements of the local authorities are the signs of the Sichuan system test 9 Instructions for use Safety instructions
The generator may cause accidental injury early, and the professional history is not recognized. As long as the enterprise is correct! The knowledge of the kinetic energy of the generator set should be mastered in the safety manual of the generator set driven by the RK engine. The following safety, operation and re-ignition requirements should be included in the following:) General safety knowledge
should include the following contents,
1: Keep a certain safety distance between the generator set and the engine: Oil is flammable and has a large capacity. You cannot add oil during the operation of the engine. You cannot smoke when refueling. You can also not approach the oil container during the operation of the engine.
3! The temperature of the internal parts is high, which may cause burns. The warning sign of the engine fiber F should be issued. 4) If there is a gas layer in the engine, it is not allowed to operate in an unrealistic room. When the unit is installed in a room with good ventilation, you must pay special attention to the fire.
h: Electric safety Kai
includes the following internal tests:
1, gas equipment: mood power system and disease head connection parts. 2》Agricultural generator sets can also be connected to other power sources. When connected with the power system library as the user, the whole party's technical personnel on the power supply to complete the power flow card to the public power grid and the generator core correction difference. According to the current provisions of this standard, this difference is described in the use of the representative drama. 3) The power output is connected to the heat exchanger, and the circuit breaker is connected to the generator set: If the circuit breaker is replaced with a new one, it must be replaced with a circuit breaker with the same special performance characteristics. 4) If the generator set complies with the electrical modification requirements specified in 6.2.3 of this standard, the following should also be considered:) The generator is connected properly.
6) Use extended wires or movable distribution cabinets: The total length of the conductor end is 1m. The total length of the conductor end is 2.5mm, and the total length of the conductor is not more than 10ml.) The safety factor of the movable
is to fully understand the function and position of each device, whether it can be displayed or not,8—2002
The width of the electrical room shall not be less than the provisions of IEC5051:11 Section 29, and its unit is m: it shall be verified by measuring the gas and based on production and operation, and its compliance shall be controlled. 6.13 Components of electrical equipment
For electrical components that are important for safety, they shall meet the applicable IS standards and the safety performance requirements in the relevant standards. The marking of these components is the operating efficiency: when they are used in the machine, they must avoid these current requirements, and the test of the independent components must comply with the corresponding specifications: this standard is not enough. For example, if there is a separate part and the technical instructions are used, the test should be carried out according to the specified period. In this case, the total number of test materials shall be similar to the specified period. 7 Operating characteristics, power output, performance and fuel consumption. 1 Standard environmental components
Standard conditions GB/6972-1 Starting temperature:
Atmospheric pressure: 1 kPa :
Relative humidity: 3-10%:
7.2 Starting and operating conditions
The generator set that complies with this standard can be started and operated within an ambient temperature range of 15~4U. 7.3 Determination of power output, performance level and voltage tolerance 7-3.1 Prepare and start the generator set according to the instructions on the instruction card. After the compound internal combustion engine is about mn, the power generation unit shall be operated at least at the average allowable power rate and the current power rate of the power generator according to the voltage and the upper limit of the plate. The power generation unit shall be operated at least at the average allowable power rate and the current power rate of the power generator according to the no-load residual load gradually to the rated power rate.
Check whether the power and power of the power generator after heating are full of GB/12826.51997 16.:6.515.7 and 16.1 G-level specifications.
Any power can be directly measured with an internal power meter. The power rate can be obtained by calculating the reverse seven certificates and the electrician's case. During the measurement period, if the atmospheric pressure and ambient temperature at the test location are consistent with the standard environmental conditions (see 7.1), the relevant test values ​​of the internal combustion engine shall be modified according to GB/T 6C72.1: the power characteristics obtained under standard environmental conditions shall not be less than 5% of the rated frequency and power for Class H machines; for Class H machines, it shall not be less than 11% of the rated average power.
7.3.3 The fuel consumption rate of the small-rate generator line shall be calculated under the fixed power room, and the value of the single micro-6kW·h shall comply with the provisions of GB.1: The micro-consumption can be used as a unit, 7. Radio interference suppression
When designing the generator set, its monthly gas annual radio interference suppression limit range shall comply with the requirements of/12: The no-load interference limit value of the spark ignition type internal engine 31 edition
Install a large-line electric shock-resistant device, which will not have an adverse effect on the electrical and control safety of the generator set. According to tk1402G1571221, it complies with the requirements
8 Marking
The label on the old unit is solid and easy to recognize, 9
G/T 2820-B2002
8.1 Rating plate
The rated power and actual performance level of the generator set should be based on the rated power to prove the single blank standard. -TYY KANr KAa
The standard number of the electric induced unit is the cumulative number of the original tax (H672.1 The standard of the original tax is the whole hundred: Therefore, before the point of the rating, the installation site of the play industry and the environment competition can be carried out briefly, and the rating plate can be used to connect the GT industry in the second 4 The heat of the single set is to be carried out
by the recognized method to check its compliance:
3.2? Safety and information signs
The symbols of the signs should be in accordance with the provisions of the IS) heart, and the power generation must be permanent. The following instructions are given for use:) Please use it when:
: There is a change in the flue gas, please do not add a pull pool in the room where the generator is not working.
It can be ignited and the components can be properly aged. You should be aware of or use the protection control kinetic energy to reduce the aging of the components. The different types of twists and turns of the group and the requirements of the local authorities are the signs of the Sichuan system test 9 Instructions for use Safety instructions
The generator may cause accidental injury early, and the professional history is not recognized. As long as the enterprise is correct! The knowledge of the kinetic energy of the generator set should be mastered in the safety manual of the generator set driven by the RK engine. The following safety, operation and re-ignition requirements should be included in the following:) General safety knowledge
should include the following contents,
1: Keep a certain safety distance between the generator set and the engine: Oil is flammable and has a large capacity. You cannot add oil during the operation of the engine. You cannot smoke when refueling. You can also not approach the oil container during the operation of the engine.
3! The temperature of the internal parts is high, which may cause burns. The warning sign of the engine fiber F should be issued. 4) If there is a gas layer in the engine, it is not allowed to operate in an unrealistic room. When the unit is installed in a room with good ventilation, you must pay special attention to the fire.
h: Electric safety Kai
includes the following internal tests:
1, gas equipment: mood power system and disease head connection parts. 2》Agricultural generator sets can also be connected to other power sources. When connected with the power system library as the user, the whole party's technical personnel on the power supply to complete the power flow card to the public power grid and the generator core correction difference. According to the current provisions of this standard, this difference is described in the use of the representative drama. 3) The power output is connected to the heat exchanger, and the circuit breaker is connected to the generator set: If the circuit breaker is replaced with a new one, it must be replaced with a circuit breaker with the same special performance characteristics. 4) If the generator set complies with the electrical modification requirements specified in 6.2.3 of this standard, the following should also be considered:) The generator is connected properly.
6) Use extended wires or movable distribution cabinets: The total length of the conductor end is 1m. The total length of the conductor end is 2.5mm, and the total length of the conductor is not more than 10ml.) The safety factor of the movable
is to fully understand the function and position of each device, whether it can be displayed or not,1) If there is an application, the relevant test values ​​of the internal combustion engine shall be modified according to GB/T6C72.1: the power characteristics obtained under standard conditions for "human" class machines shall not be less than 5% of the rated power; for Class H machines, it shall not be less than 11% of the rated average power.
7.3.3 The fuel consumption rate of the small-rate generator line shall be calculated under the fixed power room, and the value of the single micro-6kW·h shall comply with the provisions of GB.1: The micro-consumption can be used as a unit, 7. Radio interference suppression
When designing the generator set, its monthly gas annual radio interference suppression limit range shall comply with the requirements of/12: The no-load interference limit value of the spark ignition type internal engine 31 edition
Install a large-line electric shock-resistant device, which will not have an adverse effect on the electrical and control safety of the generator set. According to tk1402G1571221, it complies with the requirements
8 Marking
The label on the old unit is solid and easy to recognize, 9
G/T 2820-B2002
8.1 Rating plate
The rated power and actual performance level of the generator set should be based on the rated power to prove the single blank standard. -TYY KANr KAa
The standard number of the electric induced unit is the cumulative number of the original tax (H672.1 The standard of the original tax is the whole hundred: Therefore, before the point of the rating, the installation site of the play industry and the environment competition can be carried out briefly, and the rating plate can be used to connect the GT industry in the second 4 The heat of the single set is to be carried out
by the recognized method to check its compliance:
3.2? Safety and information signs
The symbols of the signs should be in accordance with the provisions of the IS) heart, and the power generation must be permanent. The following instructions are given for use:) Please use it when:
: There is a change in the flue gas, please do not add a pull pool in the room where the generator is not working.
It can be ignited and the components can be properly aged. You should be aware of or use the protection control kinetic energy to reduce the aging of the components. The different types of twists and turns of the group and the requirements of the local authorities are the signs of the Sichuan system test 9 Instructions for use Safety instructions
The generator may cause accidental injury early, and the professional history is not recognized. As long as the enterprise is correct! The knowledge of the kinetic energy of the generator set should be mastered in the safety manual of the generator set driven by the RK engine. The following safety, operation and re-ignition requirements should be included in the following:) General safety knowledge
should include the following contents,
1: Keep a certain safety distance between the generator set and the engine: Oil is flammable and has a large capacity. You cannot add oil during the operation of the engine. You cannot smoke when refueling. You can also not approach the oil container during the operation of the engine.
3! The temperature of the internal parts is high, which may cause burns. The warning sign of the engine fiber F should be issued. 4) If there is a gas layer in the engine, it is not allowed to operate in an unrealistic room. When the unit is installed in a room with good ventilation, you must pay special attention to the fire.
h: Electric safety Kai
includes the following internal tests:
1, gas equipment: mood power system and disease head connection parts. 2》Agricultural generator sets can also be connected to other power sources. When connected with the power system library as the user, the whole party's technical personnel on the power supply to complete the power flow card to the public power grid and the generator core correction difference. According to the current provisions of this standard, this difference is described in the use of the representative drama. 3) The power output is connected to the heat exchanger, and the circuit breaker is connected to the generator set: If the circuit breaker is replaced with a new one, it must be replaced with a circuit breaker with the same special performance characteristics. 4) If the generator set complies with the electrical modification requirements specified in 6.2.3 of this standard, the following should also be considered:) The generator is connected properly.
6) Use extended wires or movable distribution cabinets: The total length of the conductor end is 1m. The total length of the conductor end is 2.5mm, and the total length of the conductor is not more than 10ml.) The safety factor of the movable
is to fully understand the function and position of each device, whether it can be displayed or not,1) If there is an application, the relevant test values ​​of the internal combustion engine shall be modified according to GB/T6C72.1: the power characteristics obtained under standard conditions for "human" class machines shall not be less than 5% of the rated power; for Class H machines, it shall not be less than 11% of the rated average power.
7.3.3 The fuel consumption rate of the small-rate generator line shall be calculated under the fixed power room, and the value of the single micro-6kW·h shall comply with the provisions of GB.1: The micro-consumption can be used as a unit, 7. Radio interference suppression
When designing the generator set, its monthly gas annual radio interference suppression limit range shall comply with the requirements of/12: The no-load interference limit value of the spark ignition type internal engine 31 edition
Install a large-line electric shock-resistant device, which will not have an adverse effect on the electrical and control safety of the generator set. According to tk1402G1571221, it complies with the requirements
8 Marking
The label on the old unit is solid and easy to recognize, 9
G/T 2820-B2002
8.1 Rating plate
The rated power and actual performance level of the generator set should be based on the rated power to prove the single blank standard. -TYY KANr KAa
The standard number of the electric induced unit is the cumulative number of the original tax (H672.1 The standard of the original tax is the whole hundred: Therefore, before the point of the rating, the installation site of the play industry and the environment competition can be carried out briefly, and the rating plate can be used to connect the GT industry in the second 4 The heat of the single set is to be carried out
by the recognized method to check its compliance:
3.2? Safety and information signs
The symbols of the signs should be in accordance with the provisions of the IS) heart, and the power generation must be permanent. The following instructions are given for use:) Please use it when:
: There is a change in the flue gas, please do not add a pull pool in the room where the generator is not working.
It can be ignited and the components can be properly aged. You should be aware of or use the protection control kinetic energy to reduce the aging of the components. The different types of twists and turns of the group and the requirements of the local authorities are the signs of the Sichuan system test 9 Instructions for use Safety instructions
The generator may cause accidental injury early, and the professional history is not recognized. As long as the enterprise is correct! The knowledge of the kinetic energy of the generator set should be mastered in the safety manual of the generator set driven by the RK engine. The following safety, operation and re-ignition requirements should be included in the following:) General safety knowledge
should include the following contents,
1: Keep a certain safety distance between the generator set and the engine: Oil is flammable and has a large capacity. You cannot add oil during the operation of the engine. You cannot smoke when refueling. You can also not approach the oil container during the operation of the engine.
3! The temperature of the internal parts is high, which may cause burns. The warning sign of the engine fiber F should be issued. 4) If there is a gas layer in the engine, it is not allowed to operate in an unrealistic room. When the unit is installed in a room with good ventilation, you must pay special attention to the fire.
h: Electric safety Kai
includes the following internal tests:
1, gas equipment: mood power system and disease head connection parts. 2》Agricultural generator sets can also be connected to other power sources. When connected with the power system library as the user, the whole party's technical personnel on the power supply to complete the power flow card to the public power grid and the generator core correction difference. According to the current provisions of this standard, this difference is described in the use of the representative drama. 3) The power output is connected to the heat exchanger, and the circuit breaker is connected to the generator set: If the circuit breaker is replaced with a new one, it must be replaced with a circuit breaker with the same special performance characteristics. 4) If the generator set complies with the electrical modification requirements specified in 6.2.3 of this standard, the following should also be considered:) The generator is connected properly.
6) Use extended wires or movable distribution cabinets: The total length of the conductor end is 1m. The total length of the conductor end is 2.5mm, and the total length of the conductor is not more than 10ml.) The safety factor of the movable
is to fully understand the function and position of each device, whether it can be displayed or not,
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.