JB/T 8041-1999 Machine tool fixture parts and component plugs
time:
1999-08-06 15:00:00
- JB/T 8041-1999
- in force
Standard ID:
JB/T 8041-1999
Standard Name:
Machine tool fixture parts and component plugs
Chinese Name:
机床夹具零件及部件 堵片
Standard category:
Machinery Industry Standard (JB)
-
Date of Release:
1999-08-06 -
Date of Implementation:
2000-01-01
Standard ICS number:
General, Terminology, Standardization, Documentation>>Vocabulary>>01.040.29 Electrical Engineering (Vocabulary)China Standard Classification Number:
Machinery>>Process Equipment>>J44 General Fixture
alternative situation:
JB/T 8041-1995 (original standard number GB/T 2254-1991)
Description (Translated English) / downloadSkip to download
Summary:
JB/T 8041-1999 JB/T 8041-1999 Machine tool fixture parts and components plug JB/T8041-1999 Standard download decompression password: www.bzxz.net
Standard contentSome standard content:
ICS 25. 080. 01
Standard of the Machinery Industry of the People's Republic of China
Parts and units of jigs and fixtures
The parts and units of jigs and fixtures1999-08-06 Issued
State Bureau of Machinery Industry
2000-01-01 Implementation
■ Scope
Standard of the Machinery Industry of the People's Republic of China
Parts and units of jigs and fixturesPlug piece
This standard specifies plugs with specifications of 10~50mm. 2 Referenced standards
JB/T8041—1999
Replaces JB/T8041—1995
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard was published, the versions shown were all valid. All standards are subject to revision. Parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T700-1988 Carbon structural steel
JB/T8044—1999 Technical requirements for machine tool fixture parts and components 3 Dimensions
The dimensions are shown in the following figure and table.
Dimensions of matching accessorieswww.bzxz.net
Approved by the State Bureau of Machinery Industry on August 6, 1999 and implemented on January 1, 2000
Basic dimensions
4 Technical conditions
Limit deviation hl1
JB/T8041—1999
4.1Material: Q235-A in accordance with the provisions of GB/T700. 4.2After the plug is installed in the manhole, knock and squeeze the plug to make it fit tightly with the hole. 4.3Other technical conditions are in accordance with the provisions of JB/T-8044. 5 Marking
5.1 Marking example:
Blocking piece with D=20mm:
Blocking piece 20JB/T8041—1999
Corresponding accessories, D,
Basic size
Limit deviation H11
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
Standard of the Machinery Industry of the People's Republic of China
Parts and units of jigs and fixtures
The parts and units of jigs and fixtures1999-08-06 Issued
State Bureau of Machinery Industry
2000-01-01 Implementation
■ Scope
Standard of the Machinery Industry of the People's Republic of China
Parts and units of jigs and fixturesPlug piece
This standard specifies plugs with specifications of 10~50mm. 2 Referenced standards
JB/T8041—1999
Replaces JB/T8041—1995
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard was published, the versions shown were all valid. All standards are subject to revision. Parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T700-1988 Carbon structural steel
JB/T8044—1999 Technical requirements for machine tool fixture parts and components 3 Dimensions
The dimensions are shown in the following figure and table.
Dimensions of matching accessorieswww.bzxz.net
Approved by the State Bureau of Machinery Industry on August 6, 1999 and implemented on January 1, 2000
Basic dimensions
4 Technical conditions
Limit deviation hl1
JB/T8041—1999
4.1Material: Q235-A in accordance with the provisions of GB/T700. 4.2After the plug is installed in the manhole, knock and squeeze the plug to make it fit tightly with the hole. 4.3Other technical conditions are in accordance with the provisions of JB/T-8044. 5 Marking
5.1 Marking example:
Blocking piece with D=20mm:
Blocking piece 20JB/T8041—1999
Corresponding accessories, D,
Basic size
Limit deviation H11
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- JB/T 5560-1991 Small number of teeth involute cylindrical gear reducer
- JB/T 8056-1996 Slag granulator
- JB/T 6545-1993 All-metal spring hoop hexagonal locking nut
- HG 3095-1988 Rubber flame test terminology
- GB/T 8608-1988 Low-gluten wheat flour
- JB/T 982-1977 Combined sealing gasket
- GB/T 5009.127-2003 Determination of germanium in polyester resins for food packaging and their molded products
- HG/T 2334-1992 Vulcanization accelerator TMTD
- GB/T 9112-2000 Steel pipe flange types and parameters
- HG 2957.4-1984 Determination of sulfur content of alum ore sulfate barium sulfate gravimetric method
- GB/T 19649-2005 Determination of 405 pesticide residues in cereals by gas chromatography-mass spectrometry and liquid chromatography-tandem mass spectrometry
- JB/T 5156-1991 Technical requirements for square bale balers
- GB/T 15049.5-1996 CAD standard parts graphics file geometry and characteristics specification nuts
- GB 18562-2001 Occupational exposure limits for calcium cyanamide (lime nitrogen) in workplace air
- QB/T 2637-2004 Circular knife cutting machine
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail：wymp4wang@gmail.com