JB/T 9169.7-1998 Process Management Guidelines Standardization Review of Process Documents

JB/T 9169.7-1998 JB/T 9169.7-1998 Process Management Guidelines Process Document Standardization Review JB/T9169.7-1998 Standard download decompression password: www.bzxz.net

ICS25.010
Standard of the Machinery Industry of the People's Republic of China
JB/T9169.7-1998
Guide for technological management-Review ofstandardization for technological documentation
Guide for technological management-Review ofstandardization for technological documentation1998-11-16Published
National Bureau of Machinery Industry
Implemented on 1998-12-01
JB/T9169.71998
This standard is a revision of JB/Z338.1~338.1488 "Guide for Technological Management". Only editorial revisions were made during the revision, and the main technical content remained unchanged.
This standard replaces JB/Z338.1~338.1488 from the date of implementation. All appendices to this standard are informative appendices. This standard is proposed and managed by the Mechanical Science Research Institute. The responsible drafting unit of this standard: Mechanical Science Research Institute The main drafters of this standard: Ma Xianzhi, Li Qin, Shi Junwei, Wu Cheng, Du Shanyi. 1
1 Scope
Mechanical Industry Standard of the People's Republic of China
Guide for technological management-Review of standardization for technological documentation
Guide for technological management-Review of standardization for technological documentation This standard specifies the basic tasks, review objects, contents and procedures for the review of standardization for technological documentation. This standard applies to the review of standardization for technological documentation of electromechanical products. 2 Basic tasks of the review of standardization for technological documentation 2.1 Ensure the implementation of technological standards and related standards. 2.2 Ensure the integrity and unification of technological documents. 2.3 Improve the versatility of technological documents.
3 Review objects
The review of standardization for technological documentation should mainly review product process specifications and process equipment design drawings. 4 Basis for review
a) Relevant national standards and industry standards;
b) Enterprise standards and relevant regulations.
5 Review content
5.1 Review of process procedures
a) Whether the document format and size comply with the standard requirements; JB/T9169.7-1998
replaces JB/Z338.7-88
b) Whether the terms, symbols, codes and measurement units used in the document comply with the corresponding standards, and whether the text is standardized: C) Whether the selected standard process equipment complies with the standards; d) Whether the specifications of rough materials comply with the standards; e) Whether the process dimensions, process tolerances and surface roughness comply with the standards: f) Whether the relevant requirements in the process procedures comply with safety and environmental protection standards. 5.2 Review of special process equipment drawings
a) Whether the size and format of the drawings comply with the relevant standards; b) Whether the terms, symbols, codes and measurement units used in the drawings comply with the relevant standards, and whether the text is standardized; c) Whether the filling of the title bar and detail bar complies with the standards; d) Whether the drawing and dimensioning of the drawings comply with the provisions of the national standards for mechanical drawing; e) Whether the relevant dimensions, dimensional tolerances, geometric tolerances and surface roughness comply with the relevant standards; f) Whether the selected parts and structural elements comply with the relevant standards: Approved by the State Machinery Industry Bureau on November 16, 1998 and implemented on December 1, 1998
JB/T9169.7-1998
9) Whether the selected materials, standard parts, etc. comply with the relevant standards; h) Whether the standard parts, general parts and borrowed parts are correctly selected. 6 Review procedures
6.1 The standardization review of process documents should be conducted by full-time or part-time process standardization personnel. The process documents must be signed by the "design" and "audit" (special process equipment drawings also need "process") before the standardization review can be carried out. 6.2
6.3 The standardization personnel shall make appropriate marks and records when they find problems during the review process, sign after the review is qualified, and return the problematic documents together with the review records to the original designer, and then give them to the standardization personnel for signature after modification. Disputed issues in the review should be resolved through negotiation. 6.4
People's Republic of China
Mechanical Industry Standard
Process Management Guidelines Standardization Review of Process Documents JB/T9169.7-1998
Published by the Mechanical Science Research Institute
Printed by the Mechanical Science Research Institutewww.bzxz.net
(No. 2 Shouti South Road, Beijing
100044)
Word Count XXXXXX
Format 880×1230
01/16 Print Sheet X/X
Edition x in xx month, 19XX
Printing in xX month, 19XX
Print Quantity 1-XXX
Price XXX.XX Yuan
XX-XXX
Mechanical Industry Standard Service Network: 86616916
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.