JB/T 2001.37-1999 Water system filling valve relay (Type A) (PN=31.5MPa)

JB/T 2001.37-1999 JB/T 2001.37-1999 Water system filling valve relay (type A) (PN = 31.5MPa) JB/T2001.37-1999 Standard download decompression password: www.bzxz.net

IC.s$ 23.110
Machinery Industry Standard of the People's Republic of China
JB/T 2001.1~2001.74—1999
Water system assembly and parts1999-06-28 Issued
State Machinery Industry Bureau
2(-01-U1 Implementation
1 Scope
Machinery Industry Standard of the People's Republic of China
Water system
Filling valve
Watersystcm
Servomotor (type A)
PrefiflvalveActuator(typeA
[PN=31.5 MFPa ]
This standard specifies the type, size and technical requirements of liquid-filled valve servomotors (Type A). This standard applies to dead liquid servomotors (Type A 2 Type and size
2.TN65-100mm type and size Figure 1, table [2.2N125-250 core type size connection Figure 2, table 2 A
m variable head; 2-shaped seal diagram: 3 mother: 4
+B/2001.371999
Generation 713884
Frequency pull; 5-certificate brush support: 6 guide fee: 7, dynamic rate x-[shape dense village section: 5--pressure: 1(-joint: [] flange: 12-nut: 13-burning pull diagram
National Machinery Industry Bureau 1999-06-28 approved 2000-01-01 Institute
TB/T 2x1.57.1
13/1 2(K1 37 2
JBT 2001.37.3
JRT2001.37.1
JE.T200E.3T.2
JH/T281.3.3
JBT:2001.37—1999
115 ×115
1Head:20Density:1Frequency:4-case benefit;5--sliding test;6-sleeve:7-attached seat:0-shadow step seal9 check:10-:11 nut:12-bar:13-round attachment2
JB:T 2001.37.4
J;P 2IMI17 S
JH:2X-1.376
JB-T 20G1.37.T
R/1 2001.37.8
CB-T 2001.37.9
11T 1 37.4
JB/[ 200 37.5
33:T 2G01 37.6
JB.T 3001.37.7
[B:T200..378
JRT2IM137
3 skill requirements
12×030
.2×31
JB/T2001.37—1999
125 ×125
159×1
3. Relay nominal force 315MPa, test force 42MPa: elbow nominal force 4MPa, test force 6MPa: 3.2 The liquid-filled core and the body of the switch are assembled together for testing. nxd
13: M27
16×3m
3.3 The test fluid should be consistent with: the working liquid, the connection group is maintained, E10min, there should be no static leakage in the tight places; the head is maintained at a pressure of 30nin and there should be no leakage.
3.4 ​​During assembly, the sliding rod and the seat are matched, and there should be no leakage at the wide mouth after matching. 3.5 To facilitate the installation of the pipe head, it is recommended to provide a close flange LN10 (JB/2U1.14.2 or JE/T 2001.15.1) on the 22×6mm pipe.
4 Marking example
A-type relay with a nominal diameter of 65mm: bzxZ.net
Flange (A) DN65B/T2001.371999
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.