SY/T 5280-2000 General technical requirements for crude oil demulsifiers

SY/T 5280-2000 General Technical Specifications for Crude Oil DemulsifiersSY/T5280-2000 Standard download decompression password: www.bzxz.net

ICS 71.040.30
Registration number: 6806—2000
Petroleum and natural gas industry standard of the People's Republic of China SY/T52802000
General technical conditions for crude oil demulsifiers
General technical conditions for crude oil demulsifiers2000- 03- 10 Issued
State Bureau of Petroleum and Chemical Industry
2000-10—01 Implementation
SY/T 52802000
Cited standard
Technical requirements
Inspection methods
Inspection rules
Marking, packaging, transportation and storage
SY/T 5280--2000
This standard is a revision of SY/T5280-91 "Quality acceptance inspection rules for crude oil demulsifiers". The main contents of this revision are:
The standard name is revised to "General Technical Conditions for Source Oil Demulsifiers"; Crude oil demulsifiers, test samples and standard samples are redefined; National standards are cited to standardize the sampling method of crude oil demulsifiers; Relative quantitative values ​​of physical and chemical indicators are added; The production and preservation methods of standard samples are redefined: Requirements for the packaging, transportation and storage of crude oil demulsifier products are added. From the date of publication, this standard will replace SY/T5280-91n. This standard is proposed by China National Petroleum Corporation. This standard is under the jurisdiction of the Planning and Design Institute of China National Petroleum Corporation. Drafting unit of this standard: Liaohe Petroleum Exploration Bureau Exploration and Design Institute. The main drafters of this standard are Li Zeqin, Ning Jiaqing, Gai Jun, Guo Yu, Ren Hongyu. This standard was first issued in July 1991. This is the first revision. 1 Scope
Petroleum and Natural Gas Industry Standard of the People's Republic of China General Technical Conditions for Crude Oil Demulsifiers
General technical conditions for crudc oil demulsifiersSY/T5280—2000
Replaces SY/T 5280--91
This standard specifies the technical requirements, inspection methods, inspection rules, marking, packaging, transportation and storage of crude oil demulsifiers. This standard is applicable to the performance inspection and evaluation of crude oil demulsifiers. 2 Referenced standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised, and the parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T261-1983 Flash point determination method for petroleum products (closed cup method) GB/T265-1988 Kinematic viscosity determination method and dynamic viscosity calculation method for petroleum products GB,T510-1983 Condensation point determination method for petroleum products GB/I2828-1987 Batch-by-batch inspection counting sampling procedure and sampling table (applicable to continuous batch inspection) CB/T6680-1986 General rules for sampling of liquid chemical products GB/T10111-1988 Random sampling method using random numbers Test method for performance of crude oil demulsifier (bottle test method) SY/T 5281-2000
SY/T S797-93
Evaluation method for performance of demulsifier for water-in-oil emulsion 3 Definitions
This standard does not use the following definitions.
3.1 Crude oil demulsifier Cenulsifier for crude oil is a chemical agent that can destroy crude oil emulsions.
3.2 Sample
The sample of crude oil demulsifier to be evaluated.
3.3 Standard sample
The industrial product of crude oil demulsifier with qualified quality used for reference in performance inspection. 4 Technical requirements
4.1 Performance in use
In the performance inspection and evaluation of crude oil demulsifier, the indoor demulsification and dehydration temperature, the mass concentration of crude oil demulsifier dosing and other conditions should be consistent with the actual production, or be agreed upon by the user and the inspection department. 4.1.1 Under the specified crude oil demulsification and dehydration conditions, the dehydration amount of the sample shall not be less than 90% of the dehydration amount of the standard sample. 4.1.2 If the wastewater removed from the sample visually reaches the 1" water cleanliness level specified in 9.2.1 of SY/T5797.93, it can be considered that this indicator meets the requirements: If it does not meet the requirements of "1" water phase cleanliness, the leakage of the wastewater removed from the sample shall not be greater than 120% of the oil content of the wastewater removed from the standard sample.
4.1.3 The interface condition of the demulsification and dehydration of the sample and the standard sample shall be graded according to the provisions of 19.2.3 of SY5797-93. Approved by the State Administration of Petroleum and Chemical Industry on March 10, 2000, implemented on October 1, 2000
SY/T $280--2000
The interface condition level of the demulsification and dehydration of the sample shall not be lower than the interface condition level of the standard sample. 4.2 Physical and chemical indicators
The physical and chemical indicators of the sample shall meet the requirements of Table 1 Requirements. Table 1 Physical and chemical indicators
4.3 Appearance
Lower the local minimum ambient temperature
The appearance color of the sample should be basically consistent with the standard sample, without impurities and without stratification. 5 Inspection method
5.1 Performance inspection
Inspect the performance of crude oil demulsifier in accordance with the provisions of SY/T5281. 5.2 Physical and chemical performance inspection
The physical and chemical performance inspection of the sample shall adopt the method specified in Table 2. Table 2 Inspection method of physical and chemical propertieswww.bzxz.net
Verification method
5.3 Appearance inspection
G3/]510
GB/T 261
110% of the viscosity of the standard sample
GB/T265
According to the regulations of GB/I2828, GB/T10111 and GB/T6680, take the crude oil demulsifier sample, put it into a grinding bottle, let it stand for 24 hours, and observe its color, impurities and stratification under non-direct natural light. 6 Inspection rules
6.1 Generation and storage of standard samples
6.1.1 The standard sample should be an industrial product provided by the original demagnetizing emulsion manufacturer and its performance meets the user's requirements. It will be used as a standard sample after being jointly confirmed by the user, the manufacturer and the performance inspection department. 6.1.2 The standard sample should be stored in a sealed bottle. Two copies of each standard sample should be kept, one for sealed storage and the other for product inspection. The storage base should not be less than 1kg and the storage period is two Year. 6.2 Samples
According to the provisions of GB/T2828, GB/T10111 and GB/T668D, take crude oil demulsifier samples, mix them thoroughly, and divide them into two clean, dry sealed bottles, and affix labels to indicate the production, product name, batch number and sampling date. One bottle is used for inspection, and the other is kept for reference. The storage period is 3 months. 6.3 Inspection items
Each batch of crude oil demulsifier products should be inspected for performance, physical and chemical indicators and appearance. 6.4 Inspection conditions
When testing the sample, the sample should be measured under the condition of alternating with the standard sample. 6.5 Quality judgment
6.5.1 After inspection, if the performance, physical and chemical indicators and sample appearance of the crude oil demulsifier all meet the technical requirements, the quality of this batch of crude oil demulsifier is judged to be qualified.
SY/TS280—2000
6.5.2 After inspection, if any of the performance, physical and chemical indicators and sample appearance of the crude oil demulsifier does not meet the technical requirements, the quality of the batch of crude oil demulsifier shall be judged as unqualified. 7 Marking, packaging, transportation and storage
7.1 Marking
The packaging barrels of crude oil demulsifier should have obvious signs of "Do not invert", "Fireproof" and "Toxic". The product factory certificate shall be attached, and the chemical type code, chemical name, manufacturer, product standard number, trademark, net weight, export date, batch number and shelf life shall be indicated.
7.2 Net weight of the product
The net weight error of each barrel of crude oil demulsifier product should not be greater than 1%. 7.3 Packaging
The product shall be packaged in clean, dry and sealed containers. Its packaging should meet the requirements of long-distance transportation, and the specifications can be selected according to user needs. 7.4 Transportation
During transportation, it should be loaded and unloaded gently to prevent falling, exposure to the sun, and rain. 7.5 Storage
The product should be stored in a cool and ventilated place to prevent water ingress, pay attention to fire prevention, and stay away from heat sources. The storage period is two years.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.