Automotive parts logistics plastic returnable containers—Size and technical parameters requirements

GB/T 31150-2014 Dimension series and technical requirements for plastic turnover boxes for automobile parts logistics GB/T31150-2014 Standard compression package decompression password: www.bzxz.net
This standard specifies the dimension series and technical parameter requirements for plastic turnover boxes for automobile parts logistics. This standard is applicable to plastic turnover boxes produced by injection molding.
This standard was drafted in accordance with the rules given in GB/T1.1-2009.
This standard was proposed and managed by the National Logistics Standardization Technical Committee (SAC/TC269).
The main drafting units of this standard are: Automobile Logistics Branch of China Federation of Logistics and Purchasing, Guangzhou Fengshen Logistics Co., Ltd., CHEP Logistics Equipment (China) Co., Ltd., Dongfeng Motor Co., Ltd., Shanghai Anji Auto Parts Logistics Co., Ltd., FAW Car Co., Ltd., Dongfeng Peugeot Citroen Automobile Co., Ltd., Chongqing Changan Minsheng Logistics Co., Ltd.
The main drafters of this standard are: Zhang Xinkai, Liu Zhan Ce, Zhang Xiao Ying, Ren Qi Cai, Jing Wei, Yang Yi Fu, Yu Xue Lin, Yuan Gang, Huang Bin, Zhou Xiao, Lu Wei, Meng Qing Wen, Ma Zeng Rong, Zuo Xin Yu.
The following documents are indispensable for the application of this document. For any dated referenced document, only the dated version applies to this document. For any undated referenced document, the latest version (including all amendments) applies to this document.
GB/T5737 Plastic food turnover box
JB/T5991 General requirements for ergonomics of workstation equipment

ICS53.120,55.160
National Standard of the People's Republic of China
GB/T31150—2014
Automotive parts logistics
Plastic returnable containers-Size and technical parameters requirements2014-09-03 Issued
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China Standardization Administration of China
2014-12-01 Implementation
GB/T31150—2014
Normative references
3 Terms and definitions
4 Dimensional series requirements for plastic turnover boxes
Technical requirements for plastic turnover boxes
6 Product performance test and inspection requirements for plastic turnover boxes?Plastic turnover box marking
Appendix A (informative appendix) Plastic turnover box pallet layout diagram Appendix B (informative appendix) Plastic turnover box embedded height diagram 2
This standard was drafted in accordance with the rules given in GB/T1.1-2009. This standard was proposed and managed by the National Logistics Standardization Technical Committee (SAC/TC269). GB/T31150-—2014
The main drafting organizations of this standard are: Automobile Logistics Branch of China Federation of Logistics and Purchasing, Guangzhou Fengshen Logistics Co., Ltd., CHEP Logistics Equipment (China) Co., Ltd., Dongfeng Motor Co., Ltd., Shanghai Anji Auto Parts Logistics Co., Ltd., FAW Car Co., Ltd., Dongfeng Peugeot Citroen Automobile Co., Ltd., Chongqing Changan Minsheng Logistics Co., Ltd. The main drafters of this standard are: Zhang Xinkai, Liu Zhanzhan, Zhang Xiaoying, Ren Qicai, Jing Wei, Yang Yifu, Yu Xuelin, Yuan Gang, Huang Bin, Zhou Zui, Lu Wei, Meng Qingwen, Ma Zengrong, Zuo Xinyu.
1 Scope
Automobile Parts Logistics
Dimension series and technical requirements of plastic turnover boxes This standard specifies the dimension series and technical parameter requirements of plastic turnover boxes for automobile parts logistics. This standard applies to plastic turnover boxes produced by injection molding. 2 Normative references
GB/T31150—2014
The following documents are indispensable for the application of this document. For dated references, only the dated version applies to this document. For undated references, the latest version (including all amendments) applies to this document. GB/T5737 Plastic turnover box for food
JB/T5991 Ergonomics of workstations and equipment—General requirements 3 Terms and definitions
The following terms and definitions apply to this document. 3.1
Plastic turnover box
plasticreturnablecontainer
In the logistics of automotive parts, in order to ensure the quality of parts, a rigid plastic packaging container used in conjunction with standard pallets for turnover between different logistics stations.
stackablecontainer
Stackable box
The box body is molded in one go by injection molding. The bottom and top of the box body have mutually matching protrusions and grooves to achieve the stacking of plastic turnover boxes.
Foldable boxfoldablecontainer
A plastic turnover box that can stand upright or fold after being assembled from the bottom and four walls. Note: The four walls are connected to the bottom by hinges or similar structures. 3.4
Side of plastic turnover box
plastic container width sideThe vertical surface of the plastic turnover box in the length direction. 3.5
End face of plastic turnover boxplasticcontainerlengthsideThe vertical surface of the plastic turnover box in the width direction. 3.6
External size of plastic turnover boxplasticcontainerexternal sizeThe maximum size of the plastic turnover box in the length, width and height directions. 1
-rKacadiaiKAca
GB/T31150——2014
Nesting height
The depth of the upper layer of plastic turnover boxes embedded in the lower layer of turnover boxes when they are stacked on each other. 3.8
Folded heightfoldedheight
The maximum height of the foldable box in the folded state. 4 Requirements for plastic turnover box size series
Recommended turnover box size
Plastic turnover boxes for automobile parts logistics should use stackable boxes and foldable boxes. Their external dimensions and tolerances are shown in Table 1Table 1
Applicable pallets
1200×1000
1100X1100
External dimensions
Recommended turnover box external dimensions and tolerances
Stackable boxes
300-X200-1||tt| |400X300-
600-X400
800-X600-
1000-×400
1200X500
1100/X365-
730-9X365-
650-X435
550x 365_
435-x325
365×275-0
280±!
Nesting size
8 or 16
8 or 16Www.bzxZ.net
8 or 16
8 or 16
210二1
Note: For the layout of plastic turnover boxes on pallets, see Appendix A: For the schematic diagram of nesting size, see Appendix B, 2
Foldable box
Nesting size
Unit is millimeter
Height after folding
4.2 Position and size of main accessories of plastic turnover box 4.2.1 Position and size of label holder
GB/T31150—2014
The label holder should be located in the lower center of the box surface. At least one side and one end of the plastic turnover box should be provided with a label holder.
The size of the label holder should not be less than 148mm×105mm. 4.2.2 Position and size of handles
The position of the handle should be located in the middle and upper part of the end face of the plastic turnover box. When the length of the turnover box is ≥650mm, in addition to the end face, each plastic turnover box should also be provided with a handle on the side. The position of the side handle should be set according to the relevant requirements of JB/T5991. The width (W), depth (D,) and operating clearance (D) of the handle should meet the values ​​specified in Table 2. The width (W), depth (Dt) and operating clearance (D,) of the handle are shown in Figure 1. Table 2 Plastic turnover box handle size numerical provisions handle
Width of handle (W)
Depth of handle (D,)
Operating clearance (D.)
a) Front view of handle width and depth dimensions
5 Technical requirements for plastic turnover boxes
5.1 Side wall deformation rate
The deformation rate of each side of the side wall should not be greater than 1.0%. 5.2 Stacking performance
The change rate of the height of the box should not be greater than 2%
5.3 Impact resistance
Figure 1 Handle diagram
>120mm
≥15mm
b) Handle operation gap size Loading surface diagram
For stackable empty boxes at room temperature, after free fall from a height of 4m on a hard surface, no cracks are allowed on the four walls and bottom. 3
iiKacaoiaiKAca
GB/T31150—2014
For foldable empty boxes at room temperature, after free fall from a height of 2m on a hard surface, no cracks are allowed on the four walls and bottom, and the appearance of the turnover box should be intact, and the joints should not fall apart. 5.4
Bearing capacity of the bottom of the box
The maximum deformation of the bottom plane of the box should not exceed 10mmApplicable temperature
The applicable temperature range of the turnover box is: -20℃～60℃. 6Test and inspection requirements for product performance of plastic turnover boxesThe test and inspection methods for product performance of plastic turnover boxes shall comply with the provisions of GB/T5737. Plastic turnover box identification
Plastic turnover boxes should uniformly indicate the manufacturer information, production date, material, size, weight, single box bearing and other information or be jointly determined by the supply and demand parties.
Appendix A
(Informative Appendix)
Plastic turnover box pallet layout diagram
The layout diagram of the plastic turnover box applicable to 1200mm×1000mm pallets is shown in Figure A.1. For the plan layout of the plastic turnover box suitable for 1100mm×1100mm pallets, see Figure A.2. 1200mm
1200mm
1200mm
1200mm
1200mm
1200mm
GB/T31150—2014
Figure A.1 Plan layout of the material box suitable for 1200mm×1000mm pallets 5
iKacaOiaiKAca
GB/ T31150—2014
1100mmm
1100mm
1100mm
1100mm
1100mr
1100mm
Figure A.2 Layout of material boxes for 1100mm×1100mm pallets 001
Appendix B
(Informative Appendix)
Schematic diagram of the embedded height of plastic turnover boxes
For the schematic diagram of the embedded height of plastic turnover boxes, see Figure B.1. Schematic diagram of the embedded height of plastic turnover boxes
-iiKacadiaikAca
GB/T 31150-2014
GB/T31150-2014
Print Issue H: November 11, 2014 F009A People's Republic of China
National Standard
Automotive Parts Logistics
Plastic Turnover Box Dimension Series and Technical Requirements GB/T31150-2014
Published and distributed by China Standards Press
No. 2, Hepingli West Street, Chaoyang District, Beijing (100029) No. 16, Sanlihe North Street, Xicheng District, Beijing (100045) Website spc.net.cn
Total Editorial Office: (010) 64275323 Distribution Center: (010) 51780235 Reader Service Department: (010) 68523946
China Biaowei Publishing House Printed by Huangdao Printing Factory Distributed by Xinhua Bookstores in various regions
Format 880×12301/16 Printing Sheet 0.75 Word Count 14,000 Words First Edition in November 2014 First Printing in November 2014 Book Number: 1550661-50174 Price 16.00 RMB If there is any printing error, our distribution center will replace it. Copyright infringement will be investigated
Report Phone: (010) 68510107
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.