GB/T 9074.26-1988 Spring washers for assemblies
time:
2024-08-10 01:30:00
- GB/T 9074.26-1988
- in force
Standard ID:
GB/T 9074.26-1988
Standard Name:
Spring washers for assemblies
Chinese Name:
组合件用弹簧垫圈
Standard category:
National Standard (GB)
-
Date of Release:
1988-04-16 -
Date of Implementation:
1989-01-01
Standard ICS number:
Mechanical systems and general parts>>Fasteners>>21.060.30 Washers, locking partsChina Standard Classification Number:
Machinery>>General Parts>>J13 Fasteners
Release date:
1988-04-16Review date:
2004-10-14Drafting Organization:
Machinery Standardization InstituteFocal point Organization:
National Technical Committee on Fastener StandardizationPublishing Department:
China Machinery Industry FederationCompetent Authority:
China Machinery Industry Federation
Description (Translated English) / downloadSkip to download
Summary:
GB/T 9074.26-1988 Spring washers for assemblies GB/T9074.26-1988 Standard download decompression password: www.bzxz.net
Standard contentSome standard content:
Subject content
National Standard of the People's Republic of China
Spring washers for assemblies
Singlecoll springlochwasher forgsen bly
This standard specifies the spring washers for assemblies with specifications of ×3~12mm, applicable to fasteners-assemblies. 2 Reference standards
GB94.1 Technical conditions for elastic washers Spring washers GB1237 Marking method for fasteners
GB90 Acceptance inspection, marking and packaging of fasteners 3 Dimensions
The dimensions are shown in the following figure and table.
National Machinery Industry Commission 198-04-16 Approved UDC 621. 882
GB9074.26-88
198- 01 — 01 Implementation
Specification (major thread diameter)
min (nominal)
Usually greater than zero.
4 Technical Records
Technical conditions shall be in accordance with the provisions of GB 94.1.
5 Marking
5.1 Marking method shall be in accordance with the provisions of GB1237.
5.2 Marking example:
GB 9074.26-88Www.bzxZ.net
Marking of spring washers for assemblies with a size of 4mm, material of 65Mn, heat treatment hardness HRC42~50, and no surface treatment. Washers GB9074.26
Additional instructions:
This standard is proposed by the National Technical Committee for Standardization of Fasteners. This standard is under the jurisdiction of the National Machinery Industry Committee Standardization Institute. This standard was drafted with funding from the National Machinery Industry Committee Standardization Institute. 554
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
National Standard of the People's Republic of China
Spring washers for assemblies
Singlecoll springlochwasher forgsen bly
This standard specifies the spring washers for assemblies with specifications of ×3~12mm, applicable to fasteners-assemblies. 2 Reference standards
GB94.1 Technical conditions for elastic washers Spring washers GB1237 Marking method for fasteners
GB90 Acceptance inspection, marking and packaging of fasteners 3 Dimensions
The dimensions are shown in the following figure and table.
National Machinery Industry Commission 198-04-16 Approved UDC 621. 882
GB9074.26-88
198- 01 — 01 Implementation
Specification (major thread diameter)
min (nominal)
Usually greater than zero.
4 Technical Records
Technical conditions shall be in accordance with the provisions of GB 94.1.
5 Marking
5.1 Marking method shall be in accordance with the provisions of GB1237.
5.2 Marking example:
GB 9074.26-88Www.bzxZ.net
Marking of spring washers for assemblies with a size of 4mm, material of 65Mn, heat treatment hardness HRC42~50, and no surface treatment. Washers GB9074.26
Additional instructions:
This standard is proposed by the National Technical Committee for Standardization of Fasteners. This standard is under the jurisdiction of the National Machinery Industry Committee Standardization Institute. This standard was drafted with funding from the National Machinery Industry Committee Standardization Institute. 554
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- GB 1987-1986 Food additive citric acid
- JB/T 6307.1-1992 Test methods for power semiconductor modules - Rectifier arm pairs
- QB/T 2623.3-2003 Soap test method Determination of total alkali content and total fatty matter content in soap
- JB/T 10336-2002 Supplementary technical requirements for rolling bearings and their parts
- JB/T 9904.2-1999 Spline shaft grinding machine accuracy inspection
- JB/T 50093-1997 Rolling bearing life and reliability test evaluation method
- JB/T 7686-1995 Cone-disc ring-disc type continuously variable transmission
- GB/T 21619-2008 Dangerous goods - Test method for flammable solids which in contacting with water emit flammable gases
- HG/T 2129.29-1991 Acid-resistant phenolic plastic slip-on flanges for chemical equipment parts
- GB/T 28227.2-2011 Guidelines for the implementation of the quality management system of cultural service—Part 2:Indoor museum
- GB/T 7387-1999 Technical requirements for marine reference electrodes
- GB/T 5413.1-1997 Determination of protein in infant formula and milk powder
- JB/T 5997-1992 Technical requirements for brake systems of wheeled tractor trailer units
- GB 11701-1989 Basic provisions for marine gangways
- GB 4859-1984 Basic measurement methods for anti-interference characteristics of electrical equipment
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail：[email protected]