Standard linear dimensions

This standard specifies the series of standard dimensions (diameter, length, height, etc.) commonly used in the machinery manufacturing industry within the range of 0.01 mm to 20,000 mm. This standard applies to the main dimensions with interchangeability or serialization requirements (such as installation and connection dimensions, matching dimensions with tolerance requirements, nominal dimensions that determine the product series, etc.). Other structural dimensions should also be adopted as much as possible. This standard does not apply to dependent variable dimensions derived from main dimensions, dimensions between process steps in the process, and dimensions specified in corresponding standards. GB/T 2822-2005 Standard dimensions GB/T2822-2005 standard download decompression password: www.bzxz.net
This standard specifies the series of standard dimensions (diameter, length, height, etc.) commonly used in the machinery manufacturing industry within the range of 0.01 mm to 20,000 mm. This standard applies to the main dimensions with interchangeability or serialization requirements (such as installation and connection dimensions, matching dimensions with tolerance requirements, nominal dimensions that determine the product series, etc.). Other structural dimensions should also be adopted as much as possible. This standard does not apply to dependent variable dimensions derived from main dimensions, dimensions between process steps, and dimensions specified in existing corresponding standards.

TC.9 17. 020
National Standard of the People's Republic of China
GB/T 2822—2005
Replaces GH/T28231981
Standard dimensions
Standard linear dimensions
Published on 2005-05-16
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China Administration of Standardization of the People's Republic of China
Implemented on 2005-12-01
GH/T 2822——2005
The standard sizes specified in this standard are based on the GB/T32-2000 priority numbers and priority number systems and GB/T32-2000 priority numbers and priority number systems. This is conducive to the coordination, optimization and elimination of the narrow and different sizes in the machinery manufacturing industry. This standard mainly refers to the GB/T2k22-19H: standard size 1> the writing rules of our standard This standard replaces GB/2822-1U.3. This standard is proposed by the National Technical Committee for Standardization of Product Size and Geometry Specifications and drafted by the following units: China Machinery and Fuel Institute, China Machinery Science and Technology Promotion Center ... GB/T2822—2005
This standard defines the series of commonly used standard scales (diameter, length, height, etc.) in the range of 0.01mm~20000mm in the small machinery manufacturing industry.
This standard uses the main scales that are interchangeable or require serialization (such as installation and connection dimensions, matching dimensions with tolerance requirements, nominal dimensions that determine product series, etc.), and other structural dimensions should also be used as much as possible. This standard does not apply to dependent variable scales derived from main dimensions. Only small-scale works with dimensions that have been specified in corresponding standards shall have corresponding standards. 2. Specification of cited documents
The following documents shall become the referenced items in this standard through the use of standard conventions. For any cited document with a date notified, all subsequent revisions (excluding errors) or edited versions shall not be applicable to the standard within half a month. However, the new versions of these documents may be used according to the research and development of the suitability of this standard: For any cited document without a date notified, its latest versions shall be used for this standard. GH/T32: Priority numbers and priority number systems (ISO3.TT) B:197 Guide for the selection of priority numbers and priority number rounding value series (497.11DT) 3 Standard size series
size.1mm~2n0mmn The standard size series of the model drawing specifies the standard sizes listed in Table 7 Table 1~Table 7. The priority numbers and their rounding value series selected according to C/TH21 and B/T19764 are represented by R. Table 1 0.01 mm~0.5 mm standard size series K'
Note: The color of the R' series, R must list the chemical integer of the corresponding priority number K*20
0, 030
3, 153
The unit is in mm
G:B/T 2822—2005
3, 563
Table 20.1 nm~1.0 mm standard size series K
, K is the color of the series, K is the chemical integer of the corresponding priority number, K'15
Table 31.0 mm~10.0 mm standard size series R
: The color of the series, R must list the chemical integer of the corresponding priority number 2
The unit is in mm
-03, 3
410mm～100mm standard size series
Method: The black character after R is R system to calculate the optimal chemical recovery position Rin
GB/T2822—2005
Unit is millimeter
CB/T28222005
Table 5100mm~1000mm standard size series
: The black character after R is R system to calculate the optimal chemical recovery position Rin
GB/T2822—2005
Unit is millimeter
CB/T28222005
Table 5100mm~10000mm standard size series
GE/T2822—2005
GB/T 2822—2005
12 tx:
15 cor:
4 Standard size selection
Table 7100m20000mm standard size series
11 2:k:
16 coc
so cox
12 500
Single for metersbzxz.net
4.1 When selecting standard size series and single size, you should first select: H in the required R series and give priority to the basic series and its single size in the order of R10.R20.R40. 4,2 If you must choose, you can select the standard size in the corresponding R series. The selection order is K5, R20, Ra4o
4.3 In addition to the basic series listed in each table, you can also use a composite series to derive a series derived from a certain basic series.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.