GB/T 4683-1993 Turret lathe accuracy

This standard specifies the requirements for geometric accuracy and working accuracy of turret lathes and return wheel lathes and their inspection methods. This standard applies to turret lathes and return wheel lathes with a maximum bar diameter of 80mm or less and turret lathes with a maximum rotation diameter of 800mm or less on the bed. This standard does not apply to vertical turret lathes. GB/T 4683-1993 Turret Lathe Accuracy GB/T4683-1993 Standard Download Decompression Password: www.bzxz.net

National Standard of the People's Republic of China
Turret lathes-Tcsting of the accuracy1Subject content and scope of application
GB/T4683-93
Replaces GB4683
This standard specifies the requirements for the geometric accuracy and working accuracy of turret lathes and return wheel lathes and their inspection methods. This standard applies to turret lathes and return wheel lathes with a maximum bar diameter of 80mm or less and turret lathes with a maximum rotating diameter of 800mm or less on the bed.
This standard does not apply to vertical turret lathes. 2 Reference standards
GB 1958 Form and position tolerance inspection regulations General rules for precision inspection of metal cutting machine tools
JI3 2670
3 Important notes
3.1 When using this standard, refer to JB2670, especially the installation before precision inspection, the idle running and heating of the spindle and other components, the inspection method and the precision of the inspection tools.
3.2 Before the precision inspection of the machine tool, refer to Article 3.1 of JB2670 to check the installation level of the whole machine tool. Place a special bridge plate on the guide rail of the bed, and place a level on it. The readings of the level in the longitudinal and transverse directions shall not exceed 0.04/1000. 3.3 The sequence number of the inspection items in this standard does not indicate the actual inspection sequence. In order to install and disassemble the inspection tools and the inspection method, the inspection can be carried out in any order.
3.4 ​​The working precision inspection should be precision turning. The cutting amount, tool type and shape, and test piece material are all specified by the manufacturer. 3.5 When the measured length is different from the length specified in this standard, the tolerance value shall be converted according to the provisions of Article 2.3 of JB2670. When the conversion result is less than 0.005nn, it shall still be calculated as 0.005mm. 3.6 According to the agreement between the user and the manufacturer, the inspection items can be increased or decreased. 3.7 The range of tolerances for each test item II of this standard is as follows: mm
Parameter name
Maximum rotating diameter on the bed
Maximum material diameter4
Approved by the State Administration of Technical Supervision on April 17, 1993 Scope 1
Scope 2
250-D≤400bZxz.net
Scope 3
Implemented on December 1, 1993
389999
00OT/1O*01
0001/80*0
000T/40 *01
0001/80
0001/fo'
Kidney River Sink
(Special Return
GB/T 4683—93
221'9s
1800°0
800°0
GB/T 4683-93
33 flavor 8#99
E2't'9's
0OT/OTG0
S1o'o1z10's||tt ||0100900*0
4683—
'&''+'t's
#8###g
2#91#s
q calling?
(Back guarantee
GB/T 4683--93
?t$*''s
“一08
器当器
0OE/S1O0
ISTO'G
468393
Isto'0
C8/9 4683
4683-93
来保回张尺
900°0
GB/T 4683—93
9胺“'9
群中中中国人民书
CI/T 4683-93
This standard was drafted by the National Technical Committee for Metal Cutting Machine Tools. This standard was drafted by Shenyang No. 3 Machine Tool Factory and Nanjing Machine Tool Factory. This standard was first issued in September 181.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.