欧洲规范1—结构上的作用力—第1-7部分：一般作用力—偶见作用力—国家附件

欧洲标准 1- 结构上的作用力

—确定了第 NF EN 1991-1-7:2006 号法国/欧洲标准信息附件 A 到 D 的使用条件。

—为方便实施第 1991-1-7:2007 号法国/欧洲标准，提供了不矛盾的补充信息。

(4) 所引用条款采用第 NF EN 1991-1-7:2007 号欧洲标准的条款。

(5) 本国家附件，结合第 EN1990 至 EN1999 号欧洲标准并由它们的国家附件作为补充，与第 NF EN 1991-1-7:2007 号法国/欧洲标准一起使用，将用于新建筑（物）的计算。在全套欧洲规范颁布之前，《为国家层面确定的参数》(NDP)，在有必要的时侯，应按照每一个项目加以确定。

(6) 除合同文件另有规定外，当第 NF EN 1991-1-7:2007 号法国/欧洲标准适用于公共合同和私人合同时，国家附件也同样适用。

(7) 本国家附件需考虑的项目使用期限，可参照第 NF EN 1990 号法国/欧洲标准及其国家附件所给出的定义。在任何情况下，此期限不能与涉及责任和保障的法律条文所规定的期限相互混淆。

(8) 《为国家层面确定的参数》被加了边框，以便更加明了。附件的其他内容为欧洲标准在法国领土上实施提供了不矛盾的补充。

6

Révision de la présente publication

Le contenu technique des publications de la CEI est constamment revu par la Commission afin d'assurer qu'il reflète bien l'état actuel de la technique.

Les renseignements relatifs à ce travail de révision, à l'établissement des éditions révisées et aux mises à jour peuvent être obtenus auprès des Comités nationaux de la CEI et en consultant les documents ci-dessous :

• Bulletin de la CEI
• Annuaire de la CEI
• Catalogue des publications de la CEI

Publié annuellement

Terminologie

En ce qui concerne la terminologie générale, le lecteur se reportera à la Publication 50 de la CEI : Vocabulaire Electrotechnique International (VEI), qui est établie sous forme de chapitres séparés traitant chacun d'un sujet défini, l'Index général étant publié séparément. Des détails complets sur le VEI peuvent être obtenus sur demande.

Les termes et définitions figurant dans la présente publication ont été soit repris du VEI, soit spécifiquement approuvés aux fins de cette publication.

Symboles graphiques et littéraux

Pour les symboles graphiques, symboles littéraux et signes d'usage général approuvés par la CEI, le lecteur consultera :

• la Publication 27 de la CEI : Symboles littéraux à utiliser en électrotechnique ;
• la Publication 617 de la CEI : Symboles graphiques pour schémas.

Les symboles et signes contenus dans la présente publication ont été soit repris des Publications 27 ou 617 de la CEI, soit spécifiquement approuvés aux fins de cette publication.

Publications de la CEI établies par le même Comité d'Etudes

L'attention du lecteur est attirée sur la page 3 de la couverture, qui énumère les publications de la CEI préparées par le Comité d'Etudes qui a établi la présente publication.

Revision of this publication

The technical content of IEC publications is kept under constant review by the IEC, thus ensuring that the content reflects current technology.

Information on the work of revision, the issue of revised editions and amendment sheets may be obtained from IEC National Committees and from the following IEC sources :

• IEC Bulletin
• IEC Yearbook
• Catalogue of IEC Publications

Published yearly

Terminology

For general terminology, readers are referred to IEC Publication 50 : International Electrotechnical Vocabulary (IEV), which is issued in the form of separate chapters each dealing with a specific field, the General Index being published as a separate booklet. Full details of the IEV will be supplied on request.

The terms and definitions contained in the present publication have either been taken from the IEV or have been specifically approved for the purpose of this publication.

Graphical and letter symbols

For graphical symbols, and letter symbols and signs approved by the IEC for general use, readers are referred to :

• IEC Publication 27 : Letter symbols to be used in electrical technology ;
• IEC Publication 617 : Graphical symbols for diagrams.

The symbols and signs contained in the present publication have either been taken from IEC Publications 27 or 617, or have been specifically approved for the purpose of this publication.

IEC publications prepared by the same Technical Committee

The attention of readers is drawn to the inside of the back cover, which lists IEC publications issued by the Technical Committee which has prepared the present publication.

2

SOMMAIRE

TABLE DES MATIÈRES

:current

Foreword

This document (EN 10216-3:2002) has been prepared by Technical Committee EC/TC 29, "Steel tubes and fittings for steel tubes", the secretariat of which is held by UNI.

This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2002, and conflicting national standards shall be withdrawn at the latest by November 2002.

This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s).

For relationship with EU Directive(s), see informative annex ZA, which is an integral part of this document.

Other Parts of EN 10216 are:

Another European Standard series covering tubes for pressure purposes is:

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.

5

ISO 657-1 : 1988 (E)

Table 1 — Dimensions and sectional properties of hot-rolled equal-leg angles (concluded)

NOTES

1. Member countries may choose, to be included in their national standards, the sizes which are required to meet their demand.
2. For the angles so chosen, only thicknesses which can be rolled in their mills to meet the demand of the users may be selected from the list of thicknesses corresponding to equal angles in table 1.
3. The sectional area has been calculated using the formula

   S = [l/2 A - l) + 0,214 6 (r_root² - 2r_toe²)] × 1/100

   where
   

   S is the sectional area, in square centimetres;
   

   l is the thickness, in millimetres;
   

   r_root is the root radius, in millimetres;
   

   r_toe is the toe radius, in millimetres;
   

   A is the leg length, in millimetres.

4. Mass is calculated on the basis of density of steel of 7,85 kg/dm³.

   4