住宅路面指南

AS 3727—1993

Australian Standard^®

Guide to residential pavements

1

AS IS

内部资料

仅供参考

张忠辉惠存

禁止一切非法目的和活动行为，否则后果自负。

NOT FOR PUBLIC RELEASE

2

This Australian Standard was prepared by Committee BD/25, Residential Slabs and Footings. It was approved on behalf of the Council of Standards Australia on 29 July 1993 and published on 11 October 1993.

The following interests are represented on Committee BD/25:

• Association of Consulting Engineers, Australia
• Australian Geomechanics Society
• Australian Institute of Building Surveyors
• Australian Timber Research Institute
• Australian Uniform Building Regulations Coordinating Council
• Building Management Authority of West Australia
• Cement and Concrete Association of Australia
• Clay Brick and Paver Institute
• Concrete Masonry Association of Australia
• Construction Industry Advisory Council, Queensland
• Department of Administrative Services—Australian Construction Services
• Division of Building, Construction & Engineering, CSIRO
• Foundation and Footings Society, Victoria
• Housing Industry Association, Australia
• Institution of Engineers, Australia
• Master Builders Australia
• Plastics Industry Association
• South Australian Department of Housing & Construction
• Steel Reinforcement Institute of Australia
• University of South Australia

Additional interests participating in preparation of Standard:

• Australian Asphalt Pavement Association

Review of Australian Standards. To keep abreast of progress in industry, Australian Standards are subject to periodic review and are kept up to date by the issue of amendments or new editions as necessary. It is important therefore that Standards users ensure that they are in possession of the latest edition, and any amendments thereto.

Full details of all Australian Standards and related publications will be found in the Standards Australia Catalogue of Publications; this information is supplemented each month by the magazine 'The Australian Standard', which subscribing members receive, and which gives details of new publications, new editions and amendments, and of withdrawn Standards.

Suggestions for improvements to Australian Standards, addressed to the head office of Standards Australia, are welcomed. Notification of any inaccuracy or ambiguity found in an Australian Standard should be made without delay in order that the matter may be investigated and appropriate action taken.

This Standard was issued in draft form for comment as DR 92076.

3

AS 3727—1993

Australian Standard^®

Guide to residential pavements

First published as AS 3727—1993.

PUBLISHED BY STANDARDS AUSTRALIA
(STANDARDS ASSOCIATION OF AUSTRALIA)
1 THE CRESCENT, HOMEBUSH, NSW 2140

ISBN 0 7262 8473 4

4

PREFACE

Work on this Guide began under the direction of Standards Australia Committee on Concrete in Buildings, and was continued by the Committee on Residential Slabs and Footings.

The preparation of this Guide is in response to a widespread need for guidance in the design and construction of residential pavements.

CONTENTS

© Copyright — STANDARDS AUSTRALIA

Users of Standards are reminded that copyright subsists in all Standards Australia publications and software. Except where the Copyright Act allows and except where provided for below no publications or software produced by Standards Australia may be reproduced, stored in a retrieval system in any form or transmitted by any means without prior permission in writing from Standards Australia. Permission may be conditional on an appropriate royalty payment. Requests for permission and information on commercial software royalties should be directed to the head office of Standards Australia.

Standards Australia will permit up to 10 percent of the technical content pages of a Standard to be copied for use exclusively in-house by purchasers of the Standard without payment of a royalty or advice to Standards Australia.

Standards Australia will also permit the inclusion of its copyright material in computer software programs for no royalty payment provided such programs are used exclusively in-house by the creators of the programs.

Care should be taken to ensure that material used is from the current edition of the Standard and that it is updated whenever the Standard is amended or revised. The number and date of the Standard should therefore be clearly identified.

The use of material in print form or in computer software programs to be used commercially, with or without payment, or in commercial contracts is subject to the payment of a royalty. This policy may be varied by Standards Australia at any time.

5

STANDARDS AUSTRALIA

Australian Standard

Guide to residential pavements

1 SCOPE

This Guide provides guidelines for the selection and construction of pavements associated with residential buildings consisting of single houses or multiple dwellings in medium density housing development. It does not apply to the design and construction of pavements in public roads or streets.

This Guide does not preclude the use of any of the following:

(a) Methods and materials of pavement construction not referred to in this Guide.

(b) Locally proved designs.

(c) Pavements designed by a chartered professional engineer.

NOTE: The purpose of this Guide is to provide recommendations for pavements, normally associated with housing. Industrial pavements are not covered by this Guide. Roads and streets should comply with the requirements of the relevant authorities.

2 REFERENCED DOCUMENTS

The following documents are referred to in this Guide:

AS

Bituminous surfacing—Sprayed work, NAASRA Technical Report, National Association of Australian State Road Authorities, January 1989

Paver Note 1, Specifying and laying clay pavers, Clay Brick and Paver Institute, February 1990

6