白蚁管理 第1部分：新建工程

Australian Standard^TM

Termite management

Part 1: New building work

1

AS IS

内部资料

仅供参考

张忠辉惠存

禁止一切非法目的和活动行为，否则后果自负。

NOT FOR PUBLIC RELEASE

2

Committee BD-074, Termite Management

This Australian Standard was prepared by Committee BD-074, Termite Management. It was approved on behalf of the Council of Standards Australia on 3 November 2000 and published on 11 December 2000.

The following interests are represented on Committee BD-074:

• Australian Building Codes Board
• Australian Consumers Association
• Australian Environmental Pest Managers Association
• Cement and Concrete Association of Australia
• Clay Brick and Paver Institute
• Construction, Forestry, Mining and Energy Union
• CSIRO Entomology
• CSIRO Forestry and Forest Products
• Forest and Wood Products Research and Development Corporation
• Housing Industry Association
• Insurance Council of Australia
• Local Government and Shires Associations of New South Wales
• Master Builders Australia
• National Registration Authority for Agricultural and Veterinary Chemicals
• Queensland Forestry Research Institute
• State Forests of New South Wales
• Total Environment Centre

Additional interests participating in the preparation of this Standard:

• Australian Institute of Building Surveyors
• Concrete Masonry Association of Australia
• Consumers Federation of Australia
• Department of Lands Planning and Environment, Northern Territory

Keeping Standards up-to-date

Standards are living documents which reflect progress in science, technology and systems. To maintain their currency, all Standards are periodically reviewed, and new editions are published. Between editions, amendments may be issued. Standards may also be withdrawn. It is important that readers assure themselves they are using a current Standard, which should include any amendments which may have been published since the Standard was purchased.

Detailed information about Standards can be found by visiting the Standards Australia web site at www.standards.com.au and looking up the relevant Standard in the on-line catalogue.

Alternatively, the printed Catalogue provides information current at 1 January each year, and the monthly magazine, The Australian Standard, has a full listing of revisions and amendments published each month.

We also welcome suggestions for improvement in our Standards, and especially encourage readers to notify us immediately of any apparent inaccuracies or ambiguities. Contact us via email at mail@standards.com.au, or write to the Chief Executive, Standards Australia International Ltd, GPO Box 5420, Sydney, NSW 2001.

This Standard was issued in draft form for comment as DR 98554.

3

Australian Standard™

Termite management

Part 1: New building work

Originated as AS CA43—1966.

Previous edition AS 3660.1—1995.

Second edition 2000.

COPYRIGHT

© Standards Australia International

All rights are reserved. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the written permission of the publisher.

Published by Standards Australia International Ltd

GPO Box 5420, Sydney, NSW 2001, Australia

ISBN 0 7337 3721 8

4

PREFACE

This Standard was prepared by the Standards Australia Committee BD-074, Termite Management, to supersede AS 3660.1—1995, Protection of buildings from subterranean termites, Part 1: New buildings.

The objective of this Standard is to provide builders, building designers, regulatory authorities, termite management system manufacturers and installers, and those people requiring termite management systems with methods of termite management for implementation during construction of new building work.

This Standard is Part 1 of a series of Standards on termite management. Other parts in the series are as follows:

This Standard utilizes notes to some of the clauses. They are designated Note 1, Note 2, and so on, and are set in smaller point size, immediately following the clause. These Notes are for information and guidance only and compliance with them is not a requirement of the Standard.

Statements expressed in mandatory terms in notes to tables are deemed to be requirements of this Standard.

The terms ‘normative’ and ‘informative’ have been used in this Standard to define the application of the appendix to which they apply. A ‘normative’ appendix is an integral part of a Standard, whereas an ‘informative’ appendix is only for information and guidance.

Standards Australia draws attention to the fact that it is claimed that compliance with this Australian Standard may involve the use of patents concerning stainless steel mesh and graded stone particle termite barriers.

Standards Australia takes no position concerning the evidence, validity and scope of these patent rights.

The holders of these patent rights have assured Standards Australia that they are willing to negotiate licences under reasonable and non-discriminatory terms and conditions with applicants throughout Australia. In this respect, the statements of the holders of these patent rights are registered with Standards Australia.

Attention is drawn to the possibility that some of the elements of this Australian Standard may be subject to patent rights other than those identified above. Standards Australia shall not be held responsible for identifying any or all such patent rights.

Future editions of this Standard will not include proprietary or patented systems. While reference will be made to the existence of such systems, each system manufacturer must demonstrate compliance with the performance criteria of this Standard, where required.

5

CONTENTS

6